nvent RAYCHEM BTV Installation And Maintenance Manual Download Page 46

Page: 46 / 48

42 | nVent.com

FM Required Installation Record for Class I, Division 1,

Hazardous Locations

To complete the FM approval process, this complete form

must be returned to the nVent Customer

Service Center (fax number (800) 527-5703)

Company name _____________________________________________

Purchase order no. __________________________________________

Circuit ID no. ________________________________________________

Ref. drawing(s) _____________________________________________

Area ________________________________________________________

Autoignition temp. (AIT):

____________________________________

Group classification:

________________________________________

Heater circuit

Heater type:

_________________________________________________

Supply voltage:

_____________________________________________

Circuit length:

_______________________________________________

Maximum pipe temp:

________________________________________

Temp ID (T-rating)

___________________________________________

Components

Power connection

Splice:

______________________________________________________

Tee

End seal:

____________________________________________________

Ground-fault equipment

Make and model:

____________________________________________

Device trip level:

____________________________________________

Installation instructions

Correct components per manufacturer’s specification:

______________________________________________________________________________

Seal fittings opened and inspected (properly poured):

_______________________________________________________________________________

Ground-leakage device tested:

______________________________________________________________________________________________________

Insulation resistance testing

Use 2500 Vcd for Self-Regulating and Power-Limiting cables
Instrument used:

____________________________________________

Calibration date:

As measured on the pipe before insulation installed*

Test value

Date

Initials

Insulation resistance between conductor and braid (Test A)

_________________________________________________________________________

Insulation resistance between braid and pipe (Test B)

_______________________________________________________________________________

As measured after insulation installed*

Test value

Date

Initials

Insulation resistance between conductor and braid (Test A)

_________________________________________________________________________

Insulation resistance between braid and pipe (Test B)

_______________________________________________________________________________

* Minimum insulation resistance must be 1000 MΩ

Circuit ready to commission

Prepared by

Company

Date

Approved by

Company

Date

Installation and Inspection

Records

Summary of Contents for RAYCHEM BTV

















































Search results

Summary of Contents for RAYCHEM BTV

Reviews:

Related manuals for RAYCHEM BTV

Brands by name

Popular brands

nvent RAYCHEM BTV, Installation And Maintenance Manual

Search results

Summary of Contents for RAYCHEM BTV

Reviews:

Related manuals for RAYCHEM BTV

Brands by name

Popular brands