background image

50  |  nVent.com/ERICO 

NOTICE

Users are advised that the nVent ERICO System 

3000

 Lightning Protection System 

may not function to its full efficiency under ice or snow conditions or on chimneys or 
stacks emitting gasses or pollutants. For advice on temperature or corrosion concerns, 
please contact your local nVent ERICO Distributor.

When performing a 

3

–pole ground 

resistance test, it is essential that the probe 
is placed outside the sphere of influence of 
the ground electrode under test. 

To test the accuracy of the results and to 
ensure that the ground stakes are outside 
the spheres of influence, reposition the inner 
stake (probe) 

1

 meter in either direction and 

take a fresh measurement.

If there is a significant change in the reading 
(

30

%), you need to increase the distance 

between the ground rod under test, the inner 
stake (probe) and the outer stake (auxiliary 
ground) until the measured values remain 
fairly constant when repositioning the inner 
stake (probe).

MAINTENANCE RECORD

Date of 

Inspection

Lightning 

Event Counter 

Reading

Ground 

Resistance 

Readings

Check of 

Maintenance 

Points 

1

 

to 

11

Comments

Inspected 

by

1

2

3

Summary of Contents for ERICO System 3000

























































Reviews: