background image

NuPower

TM

 11B02A-TAC User Manual    

 

 

 

Rev 1.1 

able to support operation over a supply voltage range of +11 to +32 VDC. 

4.3

 

GROUND 

The signal and power grounds are tied together in the PA module.  
 

5

 

PRODUCT DISPOSAL – END-OF-LIFE

 

Safety is a guiding principle of NuWaves Engineering.  We ensure safe production and operation of our 
products, as well as end-of-life disposal.  Improper disposal can adversely affect the environment, wildlife 
and human health.  Please follow these guidelines when disposing of a NuWaves product: 
 

 

Do not remove the cover or any hardware 

 

Do not remove components from the circuit card assembly 

 

Do not incinerate 

 

Do not crush or shred 

 

Do not dispose of as unsorted municipal waste 

 

Do not export e-waste outside of the original destination country for recycling  

 

Utilize an e-Steward or ISO14001 certified e-waste recycler  

 

Consider export controls during recycler selection 

 

If  a  NuWaves  product  is  incorporated  into  a  larger  system  or  sub-system,  ensure  that  these 
guidelines are followed at system end-of-life 

 

  

 

 

Summary of Contents for NUPOWER 11B02A-TAC












Reviews: