background image

Pro He

TM

 Alarm Helium Analyzer 

 

NUVAIR 

Page 

www.nuvair.com

 

 

4.0 Operation 
 

Prior to each Analyzer use: 

1)  Turn unit on (hold on/off for 3 sec) and monitor Display for low battery warning. Replace 

battery immediately if warning appears. The display will show “On”, “(version of software) 
and then “Att” and then display the current He

 

level sensed by the analyzer sensor. 

 

 
 
 
 
 
 
 
 
 
 

 

2)  Cycle through the current settings of the analyzer.

 

a. 

Hold down the “Prog” button for 2 seconds then use the “On/Off” button to cycle 
through the two Threshold Alarm Values set, Full Scale Value, Auto shutdown time, 
and end.  

 

b. 

Adjust Alarm values at this time if needed see 

“4.2” 

 

3)  Confirm calibration of Analyzer using “Calibrated Test Gas”

 

 

 

 

Tip: You can check the battery life and current temperature by holding Adjust button for 3 
seconds. The display will alternate from battery life to current temperature (Celsius) twice before 
returning the home screen. 

   

 

 

Gas, even under moderate pressures, can cause extreme bodily harm. Never allow any 
gas stream to be directed at any part of your body. 
 

 

Never expose the sensor to pressures above atmospheric pressure (0 P.S.I.) or you may 
cause damage to the sensor and/or receive false readings.  Damaged Sensors will not 
provide accurate gas analysis.  Inaccurate gas analysis can lead to serious personal 
injury or death.

 

 
The Pro He

TM

 can be used to monitor an enclosed space or to analyze a regulated gas sample 

flow, the contents of a gas cylinder, or the flow from a regulator: 
 

  If monitoring an enclosed space, simply remove the Flow Adapter Cap to expose the Sensor 

face to the atmosphere and allow 15 seconds for the Display reading to stabilize. 

  If analyzing a gas flow, the Sample Flow Method is the preferred method.  The flow rate 

must equal 0.5 to 1 L/min at atmospheric pressure (1 bar).  To produce this flow, a Flow 
Restrictor and Regulator may be required.  Contact Nuvair if you need assistance. 

Low Battery 

Indication 

Ready For 

Gas Analyzing 

Summary of Contents for PRO HE

























Reviews: