NuTone QTXEN110HFLT Instructions Manual Download Page 4

Page 4

MODEL  QTXEN110HFLT   

SERVICE PARTS

99045668A

  Key No.  Part No. 

Description

  1  97016466 Housing

 

97016450 

Duct Connector-6”

 

98010102 

Wiring Plate

 

99170245 

Screw, #8-18 X .375

 

97017086 

Wire Panel/Harness Assembly

 

97020051 

Blower Assembly

 

97020052 

Control Assembly

 

97016967 

Grille Assembly 

 

 

 

  (includes key nos. 9, 10, 11 & 14)

 

99140199 

Grille Spring (2 req’d)

 

10 

99271381 

Bulb, GU24, 18W Fluorescent

 

 

 

  (2 req’d)

 11  99111345 Lens

 

12 

97018014 

Spacer (2 supplied)

 

13 

QTNHB1 

Hanger Bar Kit

 

14 

99271344 

Sensor Wire Harness

 

15 

99420665 

Thumbscrew, #8-18 x .375

INSTALL GRILLE

1.  Finish ceiling.

 

Install ceiling material. Cut out around housing.

2.  Plug in wiring.

 

Plug wiring into the proper receptacles.

3.  Attach grille to 

housing.

 

Squeeze grille springs and 

insert them into slots on 

each side of housing.

5.  Remove light lens.

 

Carefully insert a small flat-

blade screwdriver between 

grille and lens. Pry lens 

out.

4.  Push grille against 

ceiling.

6.  Install light bulbs.

 

Fluorescent bulbs sup-

plied. Purchase a 4W in-

candescent night-light bulb 

and screw bulbs into their 

sockets. Replace lens.

WARRANTY

Replacement parts can be 

ordered on our website. 

Please visit us at 

www.nutone.com

Order service parts by “Part No.” - not by “Key No.”

NUTONE THREE YEAR LIMITED WARRANTY

NuTone warrants to the original consumer purchaser of its products that such products will 

be free from defects in materials or workmanship for a period of three years from the date of 

original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, 

BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE.

During this three-year period, NuTone will, at its option, repair or replace, without charge, any 

product or part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This 

warranty does not cover (a) normal maintenance and service or (b) any products or parts which 

have been subject to misuse, negligence, accident, improper maintenance or repair (other than 

by NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of an implied warranty is limited to the three-year period as specified for the 

express warranty. Some states do not allow limitation on how long an implied warranty lasts, 

so the above limitation may not apply to you.

NuTone’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE 

PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL 

NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT 

OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow 

the exclusion or limitation of incidental or consequential damages, so the above limitation 

may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary 

from state to state. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify NuTone at the address or telephone number 

stated below, (b) give the model number and part identification and (c) describe the nature of 

any defect in the product or part. At the time of requesting warranty service, you must present 

evidence of the original purchase date.

Broan-NuTone LLC    Hartford, Wisconsin    www.nutone.com    888-336-3948

SERVICE NOTE

 

To remove Blower Assembly: 

Unplug motor. Remove thumbscrew 

(15)  from motor plate flange. Find 

the single 

TAB

 on the motor plate 

(located next to the receptacle). 

Push up near motor plate tab while 

pushing out on side of housing. Or 

insert a straight-blade screwdriver 

into slot in housing (next to tab) and 

twist screwdriver.

Summary of Contents for QTXEN110HFLT









Reviews: