background image

NuPrime 

 

 

FCC Notice - Declaration of Conformity Information

 

 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful 
interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if 
not  installed  and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 
communications. 
 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment 
does  cause  harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 
equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the 
following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 
connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

WARNING:

 Only peripherals complying with the FCC class B limits may be attached to this equipment.  

 
Changes or modifications made to this equipment, not expressly approved by us or parties authorized by us 
could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and 
(2)  this  device  must  accept  any  interference  received,  including  interference  that  may  cause  undesired 
operation. 
 

Notice  for  customers:  The  following  information  is  only  applicable  to  equipment  sold  in  countries  applying  EU 
Directives. 

EU Declaration of Conformity 

 

 

Hereby, NuPrime Audio, Inc. declares that this device is in compliance with the 
essential requirements and other relevant provisions of Directive 2004/108/EC. 

 
The manufacturer of this product is NuPrime Audio, Inc., 1712 Pioneer Ave. Ste 1817, Cheyenne, Wyoming 
82001, USA 
The  Authorized  Representative  for  EMC  and  product  safety  is  NuPrime  Audio,  Inc.,  1712  Pioneer  Ave.  Ste 
1817, Cheyenne, Wyoming 82001, USA. 
For  any  service  or  guarantee  matters  please  refer  to  the  addresses  given  in  separate  service  or  guarantee 
documents. 
 

For customers in Europe 

Summary of Contents for HPA-9














Reviews: