WARNING:
WARNING:
This tool has been shipped completely
assembled.
Carefully remove the tool and any accesso-
ries from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call 1-888-669-5672.
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
Allow battery to cool down before
charging if the battery is hot after
continuous use.
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
INPUT:
120-240V, 50/60Hz
BATTERY:
18V, 2.0Ah, 36Wh
ANVIL SIZE:
1/2”
NO-LOAD SPEED:
0-2,200 RPM
MAX TORQUE:
170 FT-LB
POWERFUL MOTOR:
Delivers up to 170 ft-lb of torque and a free
speed up to 2,200 RPM.
VARIABLE SPEED TRIGGER:
Adjust the speed of the tool by changing the
amount of trigger depression.
LITHIUM-ION BATTERY:
High-capacity 2.0Ah lithium-ion battery
features enhanced battery life and power level
indicator.
COMPACT DESIGN:
Ergonomic design allows access to tight areas
and reduces fatigue.
LED LIGHT:
Bright LED light illuminates dimly lit work areas.
UNPACKING
SPECIFICATIONS
OPERATION
INSTALLING/REMOVING BATTERY
PACK
VARIABLE SPEED SWITCH TRIGGER
To install, simply slide the battery pack and
make sure the latch on the battery snaps in
place and battery pack is secured to the tool.
To remove, depress the latch on both sides of
the battery and pull out the battery pack.
The variable speed switch trigger delivers
higher speed with increased trigger pressure
and lower speed with decreased trigger
pressure.
To turn on the tool, depress the switch trigger.
To turn it off, release the switch trigger and
allow the tool to come to a complete stop.
LED LIGHT
The LED light illuminates when the trigger is
depressed. The time-out feature will automati-
cally shut off the lights when the tool is not in
use.
CHARGING THE BATTERY
1. To charge the battery, simply insert the
charger cable to the battery charging port.
2. The battery indicator light should turn from
green to red when the battery is charging.
3. When the indicator light has turned green
the battery should be fully charged.
ROTATION DIRECTION SWITCH
(FORWARD / REVERSE / LOCK)
Set the rotation direction switch in the OFF
(Center lock) position to lock the trigger and
help prevent accidental starting when not in
use.
Push the direction of rotation switch to the left
of the trigger for forward operation. Push the
switch to the right to reverse the direction.
The tool will not run unless the direction of
rotation selector is pushed fully to the left or
right.
FEATURES
Keep the tool and its handle dry, clean and free
of oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline,
petroleum-based products, or any strong
solvents to clean your tool.
Never use gasoline or other flammable liquids to
clean the tool. Never use the tool in the presence
of flammable liquids or gases. Vapors could
ignite by a spark and cause an explosion which
will result in death or serious injury.
Do not use the tool as a hammer.
Never press the trigger of the tool when it is not
intended to be used.
Do not drop or throw the tool. Dropping or
throwing the tool can result in damage that will
make the tool unusable or unsafe. If the tool has
been dropped or thrown, examine the tool
closely for bent, cracked or broken parts. STOP
and repair before using or serious injury could
occur.
Only use accessories that are identified by the
manufacturer for the specific tool model.
Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of
injury.
Tool service must only be performed by a
qualified repair personnel.
TOOL SERVICE
The charger’s power plug must match the outlet.
Never modify the plug or try to plug the tool into
an outlet that does not match the plug.
Avoid contact with grounded elements such as
metal tables, pipes, ranges or refrigerators.
Contact with these elements can put you at risk
of electrical shock.
When operating the tool keep tool away from
wet conditions. Wet tools can cause electrical
shock.
Always inspect electrical cord for damage before
and after use. A damaged cord can cause
electrical shock.
ELECTRICAL SAFETY
Do not store batteries in areas that can reach or
exceed 105°F. (Such as outside sheds or metal
buildings in the summer).
Only charge the battery with a charger recom-
mended by the manufacturer. Use of any other
charger may cause risk of injury or fire.
Do not use chargers for anything other than
charging manufacturer recommended batteries,
otherwise electric shock could occur.
Do not expose the charger to rain nor snow.
Make sure the charger’s cord is in an area where
it will not be damaged.
Extension cords should not be used unless
necessary. Improper use of an extension cord
can result in electric shock.
Do not place an object on top of the charger.
This could block ventilation slots and cause
excessive internal heat.
Do not use the charger if it has been subjected
to a hard blow, has been dropped, or damaged
otherwise. Take the charger to an authorized
repair center.
Do not disassemble the charger. If the charger
needs to be repaired take it to an authorized
repair center.
Before cleaning the charger make sure to unplug
it from any power source. This will reduce the
risk of an electrical shock.
BATTERY AND CHARGER USE
AND CARE
Only use batteries that are recommended for this
tool by the manufacturer. Use of any other
battery may cause risk of injury or fire.
When the battery is not in use, keep it away from
metal objects that could connect one terminal to
another. If the terminals are connected the
battery could cause fire or burns.
Keep the battery free of abusive situations, if a
battery is damaged it can eject battery liquid. If
you get in contact with the battery liquid, flush
the contact area with water. If your eye gets in
contact with the battery liquid, flush with water
and seek medical help. Battery liquid can cause
irritation or burns.
MODEL: SE18IW
HTTP://WWW.NUMAXTOOLS.COM
1-888-669-5672
03
MODEL: SE18IW
HTTP://WWW.NUMAXTOOLS.COM
1-888-669-5672
04
