Numark NS7 III User Manual Download Page 14

Page: 14 / 26

Effects Controls

51.

FX 1, FX 2, FX 3:

These buttons have different functions on each Deck depending on the

current FX Mode.

•

Single-FX Mode:

FX 1

activates or deactivates the effect;

FX 2

activates or

deactivates the first effect parameter (if applicable);

FX 3

activates or deactivates the

second effect parameter (if applicable). Press and hold

Shift

and press

FX 1

to select

the desired effect. Alternatively, press and hold

Shift

and then turn the

FX Knob

under the effect name to move quickly through the list.

•

Multi-FX Mode:

The buttons activate or deactivate the first, second, and third effects

in the effects chain, respectively. Press and hold

Shift

and press one of the buttons to

select the effect for that point in the effects chain. Alternatively, press and hold

Shift

and then turn the

FX Knob

under the effect name to move quickly through the list.

52.

FX 1 Knob, FX 2 Knob, FX 3 Knob:

These knobs have different functions on each Deck

depending on the current FX Mode.

•

Single-FX Mode:

the

FX 1

Knob

controls the “wet-dry” balance of the effect; the

2 Knob

controls the first effect parameter; the

FX 3 Knob

controls the second effect

parameter. When Touch Mode is activated, touch the

FX 1 Knob

to activate its effect,

and release the knob to deactivate it.

•

Multi-FX Mode:

The knobs control the “wet-dry” balance of the first, second, and

third effects in the effects chain, respectively. When Touch Mode is activated, touch a
knob to activate its effect, and release the knob to deactivate it.

53.

Beat

Mode:

Tap this button repeatedly at the desired tempo to set the rate of the effects’

low-frequency oscillators (LFOs). Press and hold this button to reset Beat Multiplier to the
Deck’s BPM. Press and hold

Shift

and then press this button to switch between Single-FX

Mode and Multi-FX Mode.

54.

Beat Knob:

Turn this knob to set the Time Division for the selected effects.

55.

FX Assign:

Use these buttons to apply Effect A and/or B to the corresponding channel.

You can apply Effect A and/or B to the entire Program Mix by using the

FX Send

buttons

below the Master Volume knob. (Each effect can be applied to any or all of the four
channels and/or the Program Mix.)

56.

Channel Filter:

Turn this knob to adjust the filter on the corresponding channel. The type

of filter it adjusts will depend on the Filter Mode button.

57.

Filter Mode:

Press this button to change the Filter Mode (off, Filter Roll Mode, or Filter FX

Mode), which affects the Channel Filter knobs.

•

Off:

When this button is off, the

Channel Filter

knob will apply and adjust a low-pass

filter to the corresponding channel when turned counter-clockwise or a high-pass
filter when turned clockwise.

•

Filter-Roll Mode:

Press this button once to activate Filter-Roll Mode (the button will

light solid red). The

Channel Filter

knob will apply and adjust a low-pass filter to the

corresponding channel when turned counter-clockwise or a high-pass filter when
turned clockwise. In addition, it will apply a Loop Roll to the filter and will decrease in
length as the knob moves further away from the center position. Press this button
once to deactivate Filter-Roll Mode.

•

Filter-FX Mode:

Press and hold

Shift

and then press this button to activate Filter-FX

Mode (the button will flash red). The

Channel Filter

knob will apply and adjust a low-

pass filter to the corresponding channel when turned counter-clockwise or a high-
pass filter when turned clockwise. In addition, it will adjust Parameter 1 of the effects
applied to that channel as the knob moves further away from the center position.
Press this button once to deactivate Filter-FX Mode.