manualshive.com logo in svg

Numark iCDMIX 2, Operating Instructions Manual

Share
Download
Numark iCDMIX 2 Operating Instructions Manual Download Page 18

PAGE 17

CUSTO SERVICING YOUR MIXER

CONTROLS

10. Customizing and Servicing Your Mixer

Replacing the Crossfader

This mixer features a replaceable Crossfader. The Crossfader can be
removed from the mixer by loosening the two screws at the endpoints of the fader (See illustrations at
right.) Follow the steps below for removing the top panel to have access to the Crossfader.

Customizing the Direction of the Input Selector Switches

This mixer features multi directional Input Switches that can be removed and rotated to one of eight
positions (See illustrations at right.) Each Input Selector Switch is secured to the mixer by two adjacent
screws. Be sure to make note of the current switch position and the new switch positions before rotating
the switches to prevent any uncertainty before re-securing the top panel. Follow the steps below for
removing the top panel to have access to the Input Selector Switches.

Removing the Top Panel

1. Unplug the mixer and set it on a flat surface.

2. Remove the Three Fader Knobs.

3. Remove the four screws that secure the

top panel using a #2 Philips Screwdriver.

4. Carefully remove the top panel.

CAUTION!

BEFORE REPLACING ANY PARTS, IT IS EXTREMELY

IMPORTANT TO UNPLUG THE MIXER FROM ITS

POWER SOURCE.

Summary of Contents for iCDMIX 2
























Reviews:

No comments

Brands by name

Popular brands

Load more brands