01. 09. 21. Document Number 671711
6
Nuaire |
Western Industrial Estate
|
Caerphilly
|
CF83 1NA
|
nuaire.co.uk
SVTC8
Installation Manual
8.0 MAINTENANCE
It is important that maintenance checks are recorded and that the
schedule is always adhered to, in all cases, the previous report should
be referred to.
8.1 Routine Maintenance (Every 3 Months)
•
Clean all areas of unit of dust and fibres, thoroughly inspect the
unit and its components for corrosion, acting immediately to
treat/restore any damaged areas.
•
Check sealing of motor and gland plate.
•
Check for visible damage (cracked impeller, fan cowl bent, etc.)
•
Check for excessive vibration.
•
Check insulation resistance is adequate, imperative this is checked
after prolonged shutdown.
•
Tighten fasteners.
•
All electrical connections within the unit should be tightened.
8.2 Motor / Impeller Removal
If the motor or impeller has to be removed for cleaning the following
procedures are recommended:
Inspection of the motor/impeller must be made by using the intake and
discharge openings.
•
Motor connection cables to be unfastened within metal isolator
box (A).
•
Taking care, feed the cable contact back into the unit casing.
•
Before loosening bolts (B) of the motor impeller (C) care must be
taken to prevent the unit from falling down - e.g. by using a lifting
device or elevating platform.
•
To remove motor/impeller - loosen bolts (B).
Before loosening
bolts (B) of the motor impeller (C), care must be taken to
prevent the unit from falling down i.e. by using a lifting device
or elevating platform.
•
Remove impeller from unit (C) by lowering it out of casing.
•
Re-fitting the assembly is achieved by performing the above
process in reverse order.
B
C
A
10
Removing Motor / Impeller Assembly
8.3 Motor Repair
Due to unit certification EN12101-3 and in compliance with the
construction products directive, the motor must be returned to the
motor manufacturer for replacement.
9.0 WARRANTY
The 3 year warranty starts from the day of delivery and includes parts
and labour for the first year. The labour element is subject to full,
free and safe access to the equipment as recommended by the CDM
regulations. The remaining two years covers replacement parts only.
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
Failure to maintain the unit as recommended will invalidate the
warranty.
10.0 END-OF-LIFE AND RECYCLING
Where possible Nuaire use components which can be largely recycled
when the product reaches its end-of-life:
•
Fans, motors, controls, actuators, cabling and other electrical
components can be segregated into WEEE recycling streams.
•
Sheet metal parts, aluminium extrusion, heating/cooling coils and
other metallic items can be segregated and fully recycled.
•
Cardboard packaging, wood, used filters and other paper
components can be largely recycled or fully processed in energy
from waste centres.
•
Remaining items can be further segregated for energy from waste
centres or, as a last resort, sent to landfill. Please call After Sales
Support for further information on items not listed above.
Ensure that Nuaire product is made safe from any electrical / water
/ refrigerant supplies before dismantling commences. This work
should only be undertaken by a qualified person in accordance with
local authority regulations and guidelines, taking into account all
site based risks.
11.0 AFTER SALES AND REPLACEMENT PARTS
For technical assistance or further product information, including spare
parts and replacement components, please contact the After Sales
Department.
If ordering spares please quote the serial number of the unit together
with the part number, if the part number is not known please give a full
description of the part required. The serial number will be found on the
identification plate attached to the unit casing.
Telephone 02920 858 400
Technical or commercial considerations may, from time to time,
make it necessary to alter the design, performance and dimensions
of equipment and the right is reserved to make such changes without
prior notice.
