LI-973(A)
PROGRAMMING INSTRUCTIONS
SA130
BATTERY INSTALLATION
The timer is shipped with 2 CR2032 batteries. Please follow below procedures for battery
installation.
1. Remove the timer from the wall socket.
2. Using a small flat screwdriver, pry the battery holder open. The
SA130
uses two
CR2032 batteries.
3. Install two CR2032 batteries into the battery holder, making sure that the
+
and
–
polarities match up with the diagram printed on the unit.
4. When the batteries are in place, press the battery holder back into its original position.
5. If the timer is not running after batteries are installed, you may need to reset the timer.
Using the point of a pencil, press the
RESET
button located on the front panel.
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
FRONT
TIMED
UNTIMED
5 On/Off Button
Open
Battery
Door
BATTERY INSTALLATION
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
AVANT
TEMPORISÉ
NON TEMPORISÉ
5 On/Off Button
Compartiment
des piles
ouvert
REMPLACEMENT DES PILES
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
FRENTE
TEMPORIZADO
NO TEMPORIZADA
5 On/Off Button
Abra la
puerta de
la batería
CAMBIO DE BATERÍAS
CONTACT RATINGS:
• 120VAC, 60Hz
• 15A Resistive and Inductive
• 5 A, 500 W Tungsten
• 1/2 HP Motor
Risk of electric shock
• No Serviceable parts inside- Do not open or tamper with unit.
• Plug directly into an electric outlet
• For indoor use only
• Remove timer from outlet before cleaning
• Keep children away from timer & outlet
Risk of fire
• For only 120 volt usage
• Do not use to control irons and cooking appliances, etc.
• Do not exceed the recommended electrical ratings
CAUTION:
LAMP INSTALLATION
The
SA130
has two receptacle outlets - one is an untimed extra outlet which always has
power; the other is a timed outlet which is controlled by the
SA130
timer. Make sure to
connect your lamp to the proper outlet. Please note that the total rating (untimed and
timed outlet) of lamps/appliances connected to the timer must not exceed the
SA130
rating.
SET THE CLOCK
1. Press and hold the
TIME
button until the display is flashing.
2. Press and hold the
FWD
button to rapidly advance the time forward, or the
REV
button
to rapidly change the time backward. Release button when the correct time is displayed.
PM Indicator is on the lower right corner of the display (there is no AM indicator).
Note:
While pressing either
FWD
or
REV
button the minutes will begin at a moderate
pace, then get faster. This will assist you in setting the time quickly and accurately.
3. Press the
TIME
button again or wait for 10 seconds to exit time setting mode.
4. Slide the
DST
Switch, to “+1” to increase the current time 1 hour for daylight saving
time. The
DST
Indicator is on the upper right corner of the display.
SET THE PROGRAMMED TIME
SA130 HAS 2 INDEPENDENT PROGRAMMABLE SCHEDULES.
1. Press
MODE
button until “PROGRAM 1” is displayed on the upper left corner of the
display.
2. Press and hold the
PROGRAM
button until the display flashes.
3. The display will change to show ON time for Program 1 and flash. The “ON” icon will
appear. Use
FWD
button and
REV
button to adjust ON time.
4. Press the
PROGRAM
button again or wait for 10 seconds, it will change to display OFF
time. The “OFF” icon will appear. Use
FWD
button and
REV
button to adjust the OFF time.
5. Press the
PROGRAM
button once more or wait for 10 seconds to return to normal
mode. Display will change back to show real time.
6. To program 2nd schedule, just follow step 1-5 but press
MODE
Button until “PROGRAM
2” is displayed.
TIMER OPERATION
ACTIVATING THE TIMER
After programming the timer, you need to activate a schedule. Press
MODE
button until
“PROGRAM 1”, “PROGRAM 2” or “PROGRAM 12” is displayed. Timer is in Automatic mode
and will follow schedule selected (1, 2 or both.)
NOTE:
Make sure to test that the power switch on your lamp/appliance is in the ON
position before you plug it into the timed outlet.
DEACTIVATING THE TIMER
Press
MODE
button until OFF is showing. Timer is in Manual mode and schedules are
disabled.
MANUAL OVERRIDE
To override the ON or OFF settings, press
ON/OFF
button. To activate
ON/OFF
button,
you can push on the hinged front cover. The override setting will change at the next timed
event.
This product has passed
ETL testing. It is certified
and complies with both
U.S. and Canadian product
safety standards.
ONE YEAR LIMITED WARRANTY: If this product
fails because of a manufacturing defect within
one year after purchase, we will, at our option,
either repair or replace it at no charge. Our
warranty does not cover damage caused by
accident, abuse or misuse. We assume no
further liability with respect to the sale or use
of this product. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING THE WARRANTY OF
MERCHANTABILITY. We make no warranty with
respect to the fitness of any goods for the users
particular application. This warranty gives you
specific legal rights, and you also may have other
rights which vary from state to state.
It is our intent to provide accurate and current
specification information. However, in the interest
of product improvement, TORK may alter the
specifications or constructional details without
prior notice.
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
FRONT
TIMED
UNTIMED
5 On/Off Button
Open
Battery
Door
BATTERY INSTALLATION
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
AVANT
TEMPORISÉ
NON TEMPORISÉ
5 On/Off Button
Compartiment
des piles
ouvert
REMPLACEMENT DES PILES
RESET Button 3
DST Switch 2
PROGRAM Button 4
6 TIME Button
7 FWD Button
8 REV Button
MODE Button 1
FRENTE
TEMPORIZADO
NO TEMPORIZADA
5 On/Off Button
Abra la
puerta de
la batería
CAMBIO DE BATERÍAS
FOR TECHNICAL SUPPORT: SOUTIEN TECHNIQUE : PARA COMUNICARSE CON EL SERVICIO TÉCNICO: [email protected] 877.230.7874
