Safety Instructions
Thank you for purchasing this Mini Tower Fan. Please read this instruction manual before using
your Mini Tower Fan for the first time. Keep safe for future reference.
CAUTION:
Use the fan only as described in this manual. Misuse may cause a fire or an electric shock
1.
Do not operate the fan with a damaged
power cord or plug, after it malfunctions,
has been dropped or damaged in any
way. If the power cord is damaged it
must be replaced by a qualified service
engineer to avoid a hazard.
2.
Close supervision is necessary when this
fan is used near children and pets.
3.
Always turn off the fan after use, before
cleaning or moving location.
4.
Do not insert fingers or other objects into
the fan guard.
5.
Do not operate the fan in areas where
petrol, paint or other flammable liquids
are used or stored.
6.
Do not place the fan near an open
flame, cooking or heating appliance or
hot surface.
7.
This fan is not intended for use in wet or
damp locations. Never position the fan in
an area where it may fall into a bath or
other water container.
8.
This fan should not be operated outside.
9.
Always use on a dry, level surface.
10.
Do not let the power cord hang over the
edge of a table or counter.
11.
Arrange the power cord away from an
area where it may be tripped over.
12.
Never place the power cord under a
carpet or rug.
13.
To disconnect from the power supply,
grip the plug and pull from the power
socket. Never pull by the cord.
14.
Do not hang or mount the fan on a wall
or ceiling.
15.
This product is designed for household
and light commercial use ONLY.
16.
This appliance can be used by children
aged from 8 yrs and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
Parts Description
1.
Front Panel
2.
Control Panel w. LED lights
3.
Ioniser
4.
Oscillation
5.
Base (small footprint ~ 14 x 14cm)
6.
4hr timer
7.
Sleep Mode
8.
Fan guard
9.
Carry handle
Control Panel
On/Off
~ Press to turn the unit on and off.
Speed
~ Press to select Low, Medium and High fan
speeds, press the button until the red LED light
indicates the desired speed.
Sleep Mode
~ This mode will use the set fan speed
and step down through the speeds for 30
minutes ~ for example, select sleep mode plus
High speed, the fan will alternate through Hi,
Med, & Low for 30 mins. Then fan speed will drop
to Med, and alternate between Med & Low for
30 mins, then fan speed it will drop to Low and
alternate between Low and stop for 30mins.
After this, unless the timer is set, the cycle will
start again in the selected High speed. When Med fan speed is selected, sleep mode will
alternate between med, low & stop. If low fan speed is selected sleep mode will alternate
continuously between low and stop until the unit is manually powered off or the set time is
reached.
Timer
~ You can set the run time for 1, 2 or 4 hours. Press the Timer button to move through the
timer options. If there is no red LED light showing the timer is off and operation is continuous
until the fan is manually powered off.
Oscillation (OSC)
~ Press once to activate the oscillation feature, for wide distribution of air.
Press OSC button again to stop oscillation function.
Ion
~ Press to switch on the Ioniser to release negatively charged Ions to aid air-cleaning, press
again to switch off this function. A blue LED light glows when the ION function is activated.
BS plug wiring
Wiring instructions: Should it be necessary to change the plug please note the wires in the
mains lead are coloured in accordance with the following code:
BLUE – NEUTRAL * BROWN – LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
1. The BLUE wire is the NEUTRAL and must be
connected to the terminal which is marked
with the letter N or coloured BLACK.
2. The BROWN wire is the LIVE and must be
connected to the terminal which is marked
with the letter L or coloured RED.
3. Neither wire is to be connected to the terminal
which is marked with the letter E or symbol
or coloured GREEN OR GREEN /YELLOW.
4. Always ensure that the cord grip is positioned and fastened correctly.
If a 13A (BS 1363) fused plug is used it must be fitted with a 3A fuse. If in doubt consult a
qualified electrician.
WARNING:
If the power cord is damaged it must be replaced by a qualified electrician to
avoid a hazard.
2
3