manualshive.com logo in svg

nRuiT Powerporter 10.0, Owner'S Manual, Page: 16 / 23

Share
Download
nRuiT Powerporter 10.0 Owner'S Manual Download Page 16

16 

 

Powerporter on and off

 

 

Startup steps

：

 

①

 

  Make sure the power cable is properly connected

 

②

 

  Press the POWER button. 

 

③

 

  Product boot

 

  Remarks: Before the product is turned on, the internal relay of the battery will produce 

sound when it is switched on / off, which is normal.

 

Shutdown steps

：

 

①

 

  Make sure the power cable is disconnected.

 

②

 

  Press the POWER button. 

 

③

 

  Product shutdown.

 

  Remarks: Before the product is turned off, the internal relay of the battery will produce 

sound when it is switched on / off, which is normal.

 

   Warning:

 

The  power-on  and  power-off  actions  of  the  POWER  button  are  not 

emergency operations for security incidents. If there is a safety problem in the home 
energy storage system, please disconnect the leakage switch and isolation switch (in 
the distribution box) in time. (Confirmation required).

 

Powerporter

 

Communication Interface

 

Both CAN and RS485 interfaces are responsible for the communication with the inverter, 
which  is  determined  according  to  the  adaptable  inverter.  See  CAN/RS485  interface 
definition table.

 

Connect with Inverter

 

  Ensure that the maximum continuous  charge and discharge power of DC terminal is 

less than 3000W during Powerporter operation.

 

Inverter Support List

 

GROWATT SPF 

 

Summary of Contents for Powerporter 10.0
























Reviews:

No comments