manualshive.com logo in svg

NRG Systems Hybrid XT Vane, Product Manual

Share
Download
NRG Systems Hybrid XT Vane Product Manual Download Page 10

NRG Product Manual

 

 

 

Hybrid XT Vane

  

 

 

 

 

 
 

HybridXT_Vane_Manual 
Rev 13.0 

[email protected] | Page 10 

7 February 2017 

7894 

Hybrid XT Push-Pull Output 
Turbine Control Sensor, Vane 

8797, 9234, 9319 

(Red, 

Orange

 or 

Chartreuse

 

tag) only

 

All six wires are required to provide both Vane 
signals. 
White == VL (yaw right/left) 
Yellow == VR90 (upwind/downwind) 

7901 

Hybrid XT Push-Pull Output 
Turbine Control Sensor, Anem 

4716, 4717, 8797, 
9234, 9319 

Any cable may be used; if present, Yellow (Out 
2) is not used and may be left disconnected 

8115 

Hybrid XT Coil Compatible 
Output Turbine Control 
Sensor, Anem 

4716, 4717, 8797, 
9234, 9319 

Future Product. 

8797 may be used, Yellow (Out 2) is not used 
and may be left disconnected 

9362 

Hybrid XT Vane, 4-20mA 
Output, Counter Clockwise 
 

 

4716, 4717, 8797, 
9234, 9319 

Any cable may be used; if present, Yellow (Out 
2) is not used and may be left disconnected 

9363 

Hybrid XT Vane,Push-Pull, 
Active High 

8797, 9234, 9319 

(Red, 

Orange

 or 

Chartreuse

 

tag) only

 

All six wires are required to provide both Vane 
signals. 
White == VL (yaw right/left) 
Yellow == VR90 (upwind/downwind) 

9365 

Hybrid XT Anemometer, 4-
20mA Output, 60 m/s 

4716, 4717, 8797, 
9234, 9319 

Any cable may be used; if present, Yellow (Out 
2) is not used and may be left disconnected 

 

 

 

Summary of Contents for Hybrid XT Vane






























Reviews:

No comments

Brands by name

Popular brands

Load more brands