NPI ISO-STIM 01B Operating Instructions And System Description Download Page 10

Page: 10 / 11

ISO-STIM 01B User Manual

version 1.8

page 10

4. Power Supply

The ISO-STIM 01B is powered with a special power supply (see Figure 5). The power supply
is connected to the ISO-STIM 01B with the provided 9 line SubD cable. It will only fit in one
direction.

Figure 5: Front panel (left) and rear panel (right) view of the ISO-STIM 01B power supply

The power supply is connected to mains with a standard power cord. It has a POWER ON
switch on the rear panel.

Important

: Only use the supplied power supply to power the ISO-STIM 01B. Using different

power supplies might result in damage of ISO-STIM 01B and/or power supply.

Important

: This power supply is designed for use with the ISO-STIM 01B only. Using it

differently might result in damage of the power supply.

Summary of Contents for ISO-STIM 01B












Search results

Summary of Contents for ISO-STIM 01B

Reviews:

Related manuals for ISO-STIM 01B

Brands by name

Popular brands

NPI ISO-STIM 01B, Operating Instructions And System Description

Search results

Summary of Contents for ISO-STIM 01B

Reviews:

Related manuals for ISO-STIM 01B

Brands by name

Popular brands