Novatel DL-V3 Reference Manual Download Page 60 | Manualshive

Page: 60 / 116

background image

60

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

2.32 RENAME

Rename a File on the CF Card

The

rename

command allows you to rename a file on the CF card.

The

rename

command renames a file named

filename

to

newfilename

. The

rename

command fails if

newfilename

already exists, or if

filename

is open.

Syntax

rename

filename

newfilename

Message ID = 201

2.33 RESET

Perform a Hardware Reset

The OEMV

reset

command is extended to include DL-V3 features.

2.34 SATLIMIT

Set Minimum Satellites in Position Solution

The

satlimit

command allows you to set the minimum number of SVs used in the position solution, for

a specific set of messages to be passed through a particular FILE_

n

virtual channel.

The following messages are affected by the satlimit filter:

• BESTPOS

• BESTVEL

• MATCHEDPOS

• MARKPOS

• PSRVEL

• RANGE

• RANGECMP

• RTKPOS

• RTKVEL

The satlimit filter does not guarantee that

every

message in the above list which passes through this

filter is forwarded/rejected as desired. As the tracking environment changes on the GPS receiver, there
is an approximately 2 second delay between the time that a change occurs in the number of SVs used
n position solution and the time that the filter reflects this change. Consequently, during this short
period messages may be incorrectly forwarded or rejected.

Field

Data

Bytes

Format

Units

Offset

1

Header

-

-

0

2

Source filename

12

Char[]

none

H

3

Destination filename

12

Char[]

none

H+12

«
...
58
59
60
61
62
...
»

Summary of Contents for DL-V3





















































































































Reviews:

No comments

Related manuals for DL-V3

Brand: TANDBERG Pages: 23

Brand: Nauticam Pages: 6

Brand: Yaesu Pages: 42

Brand: SpeakerCraft Pages: 8

Brand: Pyle Pages: 39

Brand: Jensen Pages: 66

Brand: Farenheit Pages: 41

Brand: Icom Pages: 116

Brand: Audi Pages: 35

Brand: IDS Pages: 2

Brand: Yaesu Pages: 32

Brand: CAME Pages: 2

Brand: Hammarlund Pages: 81

AGC-4208 Series

Brand: Daewoo Pages: 52

Brand: R&S Pages: 223

Brand: BUXTON Pages: 40

Brand: Streetwize Pages: 5

Brand: VCS Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands