if Brushed Mode
is active
P6
1. iF TrAnSMiTTer iS oFF, DiSConneCT eSC FroM reCeiver
Remove input signal harness from the receiver to avoid radio interference.
2. ConneCT eSC To A ChArGeD BATTerY pACK
3. SliDe eSC’s on/oFF SwiTCh To ‘on’ poSiTion
4. wiTh eSC AT neuTrAl preSS & holD eSC’S SeT BuTTon
release EsC’s sET button once LED
is at desired setting.
To skip a parameter, press and hold ESC’s SET button to the desired parameter.
5. SeleCT pArAMeTer vAlue
LED
flashes to indicate active setting
(refer to tables at right)
. Quick press & release
SET button to select desired setting.
6. preSS & holD SeT BuTTon To STore SeleCTion
When SET button is pressed and held for about 1 second, the
new selection is
stored
in ESC’s memory—
The 4 status LEDs will scroll across to indicate ESC is
exiting programming and ESC returns to neutral.
note: There is no time constraint during selection process of custom parameters.
HAvOC SPORT ESC SOFTWARE FLOW CHART
The Havoc Sport ESC features
nine parameters
that can be adjusted.
Default settings are in bold in tables.
Transmitter can be either ON or OFF:
restOriNg factOrY defauLts:
perform one-Touch Set-up to default eSC back to factory default parameters.
THROTTLE PARAMETER SETTINGS
(Defaults in Bold)
1. MiNiMuM BraKe settiNgs (10)
BLUE LED
Amount of braking applied with first pulse of transmitter throttle information.
>>
raising this setting starts the braking at a stronger/higher level
.
setting
(# of flashes)
1
2
3
4
5
6
7
8
9
10
Minimum Brake
(%):
0
3
6
9
12 15 18 21 24 27
2. drag BraKe settiNgs (10)
BLUE & AMBER LEDs
Amount of braking applied while transmitter is at neutral. ‘Coast’ brakes.
>>raising this setting makes the motor slow down more, without
pushing the transmitter’s trigger into the brake/reverse direction.
setting
(# of flashes)
1
2
3
4
5
6
7
8
9
10
Drag Brake
(%):
0
3
6
9
12 15 18 21 24 27
3. dead BaNd settiNgs (5)
BLUE & GREEN LEDs
Space between Minimum Brake & Minimum Drive, with neutral in middle.
>>raising this setting will increase the ‘free play’, or distance your
trigger must move before forward drive or braking will begin.
setting
(# of flashes)
1
2
3
4
5
Dead Band
(%):
2
3
4
5
6
4. MiNiMuM driVe settiNgs (5)
AMBEr LED
Amount of forward drive applied with first pulse of transmitter information.
>>raising this setting makes the motor start at a stronger/higher
level so it takes off more aggressively from neutral.
setting
(# of flashes)
1
2
3
4
5
Minimum Drive
(%):
1
2
3
4
5
5. tHrOttLe curVe seLectiON* (2)
GrEEN LED
>>Changing this setting changes the throttle response and ease of
driveability.
Note: Setting is fixed at “Linear” in Brush Mode.
setting
(# of flashes)
1
2
Throttle Curve
:
Linear
expo
6. BraKe freQueNcY* (7)
rED LED
>>raising this setting makes the brake response smoother and
more controllable.
setting
(# of flashes)
1
2
3
4
5
6
7
Brake Frequency
(KHz)
:
1
2
3
4
5
7.5
8
7. reVerse* (2)
RED, GREEN & AMBER LEDs
>>Changing this setting activates/deactivates reverse direction.
setting
(# of flashes)
1
2
reverse
(On/Off):
Off (FWD/BRK)
on (FwD/BrK/rev)
8. MOtOr rOtatiON* (2)
RED, GREEN & BLUE LEDs
>>Changing this setting changes direction of motor rotation.
setting
(# of flashes)
1
2
Motor rotation
(CCW/CW):
CCw
q
CW
p
9. Li-PO cut-Off (2)
RED & AMBER LEDs
>>Changing this setting enables/disables li-po cutoff (@6.25 volts).
setting
(# of flashes)
1
2
li-po Cut-off
(On/Off):
OFF
on
H AV O C
s p O Rt E s C C u s t O m p R O G R A m m I N G
pleASe noTe:
This page contains optional Advanced Programming items!
No further adjustments are required.
(But don’t worry, you can always reset factory defaults by performing the One-Touch programming again, so go ahead & experiment—that’s why the programming is in there, right?)
@neuTrAl
RED LED on solid
Min. BrAKe
BLUE
press & hold
press & hold
press & hold
press & hold
DrAG BrAKe
BLUE & AMBER
DeAD BAnD
BLUE & GREEN
Min. Drive
AMBER
press & hold
ThroTTle Curve*
GREEN
LEDs roll off
Exit Programming
@neuTrAl
RED LED on solid
press & hold
BrAKe FreQuenCY*
RED
press & hold
reverSe*
RED / GREEN / AMBER
press & hold
MoTor roTATion*
RED / GREEN / BLUE
press & hold
li-po CuT-oFF
RED & AMBER
press & hold
continue holding ESC
’s SET
button to skip steps here
all LEDs
flash 5 times
HAvOC SOFTWARE
FLOW CHART:
*Not adjustable
in brush mode.
