background image

WARRANTY 

NOVA TECHNOLOGY INTERNATIONAL, LLC. warrants the DOCK SENTINEL™ SAFETY GATE to 

be free of defects in material or workmanship under normal use for a period of one year from the date 

of shipment. This warranty does not cover any failure to properly maintain the product. This warranty 

is the only one given by NOVA TECHNOLOGY INTERNATIONAL, LLC. and is in lieu of all guarantees and 

warranties expressed or implied by anyone other than NOVA TECHNOLOGY INTERNATIONAL, LLC,       

including those of fitness for a particular purpose and merchantability. In order for warranty claims to be  

honored the products must have been properly installed, maintained, and operated within their intended 

function and not otherwise abused. 

 

If your DOCK SENTINEL™ SAFETY GATE  is defective in material or workmanship and you notify NOVA 

TECHNOLOGY INTERNATIONAL, LLC within one year of the date of shipment, NOVA TECHNOLOGY 
INTERNATIONAL, LLC will, at its option, repair or replace the defective component(s) at no cost to you. 

NOVA TECHNOLOGY INTERNATIONAL, LLC. will not be responsible for or pay for loss of time,              

inconvenience, loss of the use of the product, or property damage caused by this product or its failure to 

work, or any other incidental or consequential damages. 

 

 

NOVA Dock Sentinel

TM 

Installation Manual 

24 

N90W14507 Commerce Drive  Menomonee Falls, WI  53051 

Phone 262-502-1591  |  800-236-7325  |  fax 262-502-1511 

www.novalocks.com 

Summary of Contents for Dock Sentinel DG-048-000

























Reviews: