Push the menu button, MAIN SETUP will appear as right.
1. LENS MODE
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
* OSD button is used for zoom and focus before its OSD menu opens.
* You can control above functions through RS-485 communication or
COAX communication also.
1. FOCUS ADJ : This function will help you to make focus easier.
After fixing the camera, when you adjust the focus lever,
an orange bar means camera is not focused.
A green bar means the camera is in focus.
The smaller green bar is, the better focus.
2. D-ZOOM : Digital Zoom available. Range : 1.0X ~ 10X
3. ZOOM-STATUS : Turn on/ off digital zoom ratio digits.
8. SPECIAL
9. EXIT
LENS MODE
4. RETURN
1. FOCUS ADJ
2. D-ZOOM 1.0X
3. ZOOM STATUS ON
Push the menu button, MAIN SETUP will appear as right.
2. EXPOSURE
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
8. SPECIAL
9. EXIT
EXPOSURE
3. SHUTTER AUTO
1. BRIGHTNESS |======| 10
4. SENS-UP x32
2. LENS MODE ALC
5. AGC |======| 15
6. RETURN
⊙
EXPOSURE
1. BRIGHTNESS : Adjust brightness.
Range : 0 ~ 20.
2. LENS MODE : Choose iris control method ( ALC/ELC )
ALC(Auto iris Level Control) : INDOOR -> For indoor use
OUTDOOR -> For outdoor use
DEBLUR -> Suppress blurred image from fast movement
ELC(Electric iris Level Control): For fixed iris lens( NORMAL/ DEBLUR )
3. SHUTTER : Adjust shutter operation. ( AUTO / MANUAL / FLICKER )
AUTO : NORMAL / DEBLUR
MANUAL : 1/25(1/30) ~ 1/60,000
FLICKER : ANTI-FLICKER MODE
4. SENS-UP ( Digital Slow Shutter ) : It will make sense up by enhancing available light.
Range : OFF,X2~(NTSC: X60, PAL:X50 )
5. AGC : Auto Gain Control for brighter images. You can choose max. of AGC value.
Range : 0 ~ 20.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
Push the menu button, MAIN SETUP will appear as right.
3.WHITE BALANCE
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
MANUAL
3. B-GAIN |======| 10
1. KELVIN MIDDLE
4. RETURN
2. R-GAIN |======| 10
Use the White Balance function to adjust the screen color ( AUTO, AUTOext, PRESET, MANUAL )
AUTO : Under normal condition.
AUTOext : When color temperature is lower than normal condition.
PRESET : If you push SET button, it will fix the white balance value under current condition.
MANUAL : You can adjust color temperature manually.
⊙
MANUAL
1. KELVIN : It sets the standard of color temperature.
You can choose LOW, MIDDLE and HIGH.
2. R-GAIN : You can adjust gain for RED color. Range : 0 ~ 20.
3. B-GAIN : You can adjust gain for BLUE color. Range : 0 ~ 20.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
Push the menu button, MAIN SETUP will appear as right.
4.HIGH LIGHT MASK
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
You can choose High Light Mask mode.
OFF -> Not working.
ALL -> Always working day / night.
DAY -> Working only day time.
NIGHT -> Working only at night.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
HLMASK
3. RETURN
1. LEVEL |======| 10
2. COLOR BLK
⊙
HLMASK
1. LEVEL : You can set the lighting level for HL Mask to start working.
Range : 0 ~ 20.
2. COLOR : You can choose the masking color.
Black, White, Yellow, Cyan, Green, Magenta, Red and Blue.
* Setting value is same for ALL, DAY and NIGHT modes.
Push the menu button, MAIN SETUP will appear as right.
5. BACKLIGHT
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
9. EXIT
BACKLIGHT
3. SIZE ADJ OFF
1. MODE BLC
2. POSITION OFF
4. RETURN
⊙
BACKLIGHT
1. MODE : Select back light compensation ( OFF, BLC, WDR).
If you change the model,the sub-menu will be also changed.
OFF : Normal condition.
BLC : Set the window by POSITION, SIZE ADJ.
*** WDR
: WIDE DYNAMIC RANGE. You can set WEIGHT to LOW / MIDDLE / HIGH.
* When you change POSITION / SIZE, press SET KEY and change by using LEFT / RIGHT / UP / DOWN buttons.
After finishing the setting, you can save it by press SET KEY.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
Push the menu button, MAIN SETUP will appear as right.
6. DNR3
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
⊙
DNR3 : You can choose level of 2D + 3D DNR.
Range : OFF, LOW, MIDDLE and HIGH.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
Push the menu button, MAIN SETUP will appear as right.
7. DAY&NIGHT
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
DAY&NIGHT
3. DELAY 3 SEC
1. CDS LEVEL 210
2. CDS MARGIN |======| 10
4. IR MODE STATIC
5. RETURN
CDS-A/D : 00210
⊙
A.CDS(DAY&NIGHT)
1. CDS LEVEL : You can adjust the changing time from night to day.
The bigger value, the later it will change to night.
* CDS value will be shown at bottom if cursor is on CDS LEVEL menus.
2. CDS MARGIN : It is a gap between day-night change level and night-day change.
Range : 0 ~ 20.
3. DELAY : You can set the time until day mode changes to night mode.
Range : 1 ~ 10 SEC.
4. IR MODE : You can use smart IR LED function.
STATIC : LED lightning is always same. (Anti-saturation level setting is sub-menu.)
ANTI-SATURATION : 0 ~ 20
(The bigger value, the less saturation but surrounding area is getting dark.)
*** SMART
*** SMART
: It prevents the image from being whiteout by strong IR lighting.
ng IR lighting.
DAY&NIGHT
3. DELAY 3 SEC
1. AGC LEVEL |======| 10
4. RETURN
2. AGC MARGIN |======| 10
⊙
A.AGC(DAY&NIGHT)
1. AGC LEVEL : You can adjust AGC level to change day mode to night mode.
Range is 0 ~ 20.
2. AGC MARGIN : It is a gap between day-night change level and night-day change.
Range is 0 ~ 20.
3. DELAY : You can set the time until day mode to night mode.
Range is 1 ~ 10 SEC.
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
⊙
DAY&NIGHT : You can choose Day&night mode.
Range : A.CDS, A.AGC, COLOR and BW.
Push the menu button, MAIN SETUP will appear as right.
8. SPECIAL
⊙
IMAGE ADJ
1. COLOR GAIN : You can adjust the color GAIN.
Range is 0 ~ 20.
2. SHARPNESS : You can adjust sharpness of picture.
Range is 0 ~ 20.
3. MIRROR : It is a mirror image (horizontal).
4. FLIP : Flips top and bottom of picture (vertical).
5. SHADING : It is amending lens characteristic.
You can adjust SHADING WEIGHT.
6. ACE MODE (Adaptive Contrast Enhancer) : Enhances the contrast.
OFF / LOW / MIDDLE / HIGH
7. DEFOG MODE : Remove the fog or smog to make image clear.
AUTO : Adjust correct WEIGHT automatically.
MANUAL : Adjust correct WEIGHT manually ( LOW / MIDDLE / HIGH )
8. GAMMA : Set the GAMMA.
Range is 0.45 ~ 0.65.
SPECIAL
3. SYSTEM
1. IMAGE ADJ
4. PRIVACY OFF
2. INTELLIGENT
5. CAM TITLE
6. COMM ADJ
7. RESET MODE
8. RETURN
IMAGE ADJ
3. MIRROR OFF
1. COLOR GAIN |======| 13
4. FLIP OFF
2. SHARPNESS |======| 7
5. SHADING OFF
6. ACE MODE OFF
7. DEFOG MODE OFF
8. GAMMA 0.55
9. RETURN
MAIN SETUP
3. WHITE BAL AUTO
1. LENS MODE
4. HLMASK OFF
2. EXPOSURE
5. BACKLIGHT
6. DNR3 MIDDLE
7. DAY&NIGHT A.CDS
8. SPECIAL
9. EXIT
“ ” on menu means that you can go to sub-menu.
You can go to up and down by UP,DOWN buttons.
You can change the value by LEFT,RIGHT buttons.
INTELLIGENT
3. QUICK ZOOM OFF
1. MOTION ON
2. ALARM
4. RETURN
3. QUICK ZOOM OFF
4. RETURN
MOTION
3. ZONE NUMBER 0
1. DET. SETTING ON
4. WINDOW USE ON
2. WINDOW TONE 0
5. POSITION OFF
6. SIZE ADJ OFF
7. RETURN
DET. SETTING
3. MOTION EST. |======| 0
1. SENSITIVITY |======| 5
2. OBJ. KEEP LV 0
4. SIGNAL OUT ON
5. RETURN
ALARM
3. BRIGHT CHG. OFF
1. SHAKING OFF
4. BRIGHT SCL |======| 0
2. SHAKE SCALE |======| 0
5. RETURN
QUICK ZOOM
3. STANDBY 30/60sec
1. MOVING 30/60sec
4. SYNCHRONUS OFF
2. ZOOM IN 30/60sec
5. TRACKING OFF
6. REPEAT OFF
7. RETURN
⊙
INTELLIGENT : Motion detection and Quick Zoom Menu.
1. MOTION : Setting the sensitivity of movement.
1-1. DET. SETTING : Motion Detection sensitivity adjustment menu
1-1-1. SENSITIVITY : Sensitivity adjustment. Range 0 ~ 20.
1-1-2. OBJ. KEEP LV : Motion detection time adjustment.
Range 0 ~ 60.
The bigger value is, the longer it will keep.
1-1-3. MOTION EST. : Estimating the motion which may occur. Range 0 ~ 20.
The high value is, the faster it estimates.
1-1-4. SIGNAL OUT : Signal output on/off when motion is detected
1-2. WINDOW TONE : Window Tone adjustment menu
Range is 0 ~ 6.
1-3. ZONE NUMBER : You can select the zones for the motion detection.
Range is 0-3 ( total 4 areas)
1-4. WINDOW USE : You can turn on/off the motion detection
for the selected areas.
1-5. POSITION : Press SET KEY and Left, Right, Up, Down to adjust the window position.
1-6. SIZE ADJ : Press SET KEY and Left, Right, Up, Down to adjust the size.
2. ALARM : Alarm on/off adjustment and alarm sensitivity.
2-1. SHAKING : Alarm output when camera is shaken. ON/OFF
2-2. SHAK SCALE : Sensitivity for camera shaking detection. Range 0 ~ 20.
2-3. BRIGHT CHG. : Alarm output when the brightness is changed. ON/OFF
2-4. BRIGHT SCL : Sensitivity for brightness change. Range 0 ~ 20.
The value is smaller, the more sensitive.
3. QUICK ZOOM : Zoom movement setting when motion is detected.
3-1. MOVING : Zoom in/out for set frames. Range 0 ~ 240.
3-2. ZOOM IN : Zoom in for set frames. Range 0 ~ 240.
3-3. STANDBY : Keeping the full screen for set frames. 0 ~ 240.
3-4. SYNCRONOUS : Zoom in/out only for set time regardless of motion detection. ON/OFF.
3-5. TRACKING : Zoon in/out by tracking the object. ON/OFF.
3-6. REPEAT : Zoom in/out repeating for the areas where zoom in is already done. ON/OFF.
PRIVACY
3. POSITION OFF
1. ZONE NUM 0
4. SIZE ADJ OFF
2. ZONE DISP OFF
5. COLOR BLU
6. TRANS 4
7. RETURN
⊙
PRIVACY : You can mask certain areas on the screen
1. ZONE NUM : Masking zone number. It is from 0 ~ 15.
Total 16 areas.
2. ZONE DISP : You can display each PRIVACY zone one by one.
ON / OFF
3. POSITION : Adjust window position.
After pushing SET KEY, you can move the window by left, right and up, down buttons.
4. SIZE ADJ : Adjust window size. ON/OFF
After pushing SET KEY, you can move the window by left, right and up, down buttons.
5. COLOR : You can choose zone color.
( Black, White, Yellow, Cyan, Green, Magenta, Red, Blue )
6. TRANS : You can choose transparency ratio.
Range is 0 ~ 4.
CAM TITLE
3. RETURN
1. DISPLAY OFF
2. TITLE CAMERA-1
A B C D E F G H
I J K L M N O P
Q R S T U V W X
Y Z 0 1 2 3 4 5
6 7 8 9 < > - .
/ & = CLR RET
⊙
CAM TITLE
1. DISPLAY : You can display the camera title on screen.
ON / OFF.
2. TITLE : If you push SET button, you can go to editing mode.
Move the cursor by pressing UP/DOWN, LEFT/RIGHT buttons
place the cursor on the letter you want, and push SET button.
The letter you choose will be shown on text line.
If you push SET button on CLR, one letter will be erased.
If you push SET button on RET, setting will be finished.
⊙
SYSTEM
1. CVBS TYPE : Video output type.
NTSC , PAL
2. PEDESTAL : Setup level for video signal. Range 0 ~ 20.
3. LANGUAGE : You can select the menu language according to your requirements.
SYSTEM
2. SENSITIVITY |======| 10
1. CVBS TYPE NTSC
4. RETURN
3. LANGUAGE ENG
⊙
COMM ADJ
1. CAM ID : You can make camera ID for RS485 / COAX communication.
Range is 1 ~ 255.
2. BAUD RATE : Baud rate for RS485 / COAX communication.
2400, 4800, 9600, 19200.
3. UART MODE : You can set the data format for RS485 / COAX communication.
8-N-1 : data bit 8 , parity None , STOP bit 1
8-O-1 : data bit 8 , parity ODD , STOP bit 1
8-E-1 : data bit 8 , parity EVEN , STOP bit 1
4. RS485 : ON / OFF RS485 communication.
You should set it OFF when you do not use RS485 communication.
5. DIPS ID : Camera address will be displayed when you use RS485 / COAX communication.
6. PROTOCOL : Protocol for RS485 / COAX communication.
PELCO-D , PELCO-P , D-MAX protocols are available.
7. COAX : You can turn on / off coaxial communication.
You should set it OFF if you do not use RS485 communication.
COMM ADJ
3. UART MODE 8-N-1
1. CAM ID 1
4. RS 485 ON
2. BAUD RATE 9600
5. DISP ID OFF
6. PROTOCOL PELCO-D
7. COAX OFF
8. RETURN
⊙
RESET MODE : ** RESET MODE is for factory use only. Don’t change it.
1. PROFILE : Set the RESET condition according to camera type.
Do not change it. (Manufacturer’s menu)
2. CDS LEVEL : Set CDS LEVEL for RESET
3. ANTI-SAT : Set ANTI-SATURATION value for RESET
4. RST-BRIGHT : Set BRIGHTNESS value for RESET
5. RESET : Push SET button and hold until PUSH message appears.
If iti is properly done, all the camera values will be changed to factory default.
RESET MODE
3. ANTI-SAT 8
1. PROFILE N-O-C
4. RST-BRIGHT 7
2. CDS LEVEL 210
5. RESET ON
6. RETURN
Troubleshooting
If you have trouble operating your camera, refer to the following table. If the guidelines
If you have trouble operating your camera, refer to the following table. If the guidelines
do not enable you to solve the problem, contact an authorized technician.
do not enable you to solve the problem, contact an authorized technician.
The DAY/NIGHT menu does not work.
The DAY/NIGHT menu does not work.
▶
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
The SENS-UP function does not work.
The SENS-UP function does not work.
▶
Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶
Check that SHUTTER of EXPOSURE SETUP menu is ‘FLICKER’ or ‘MANUAL’.
Nothing appears on the screen.
Nothing appears on the screen.
▶
Check that the power cord and line connection between the camera and monitor are fixed properly.
▶
Check that you have properly connected BNC cable to the camera.
The image on the screen is dim.
The image on the screen is dim.
▶
Is the lens stained with dirt? Clean your lens with a soft, clean cloth.
▶
Check the monitor and DVR settings.
▶
If the camera is exposed to very strong light, change the camera position.
The image on the screen is dark.
The image on the screen is dark.
▶
Adjust the contrast feature of the monitor .
▶
If you have an intermediate device, set the 75Ω / Hi-z properly.
The camera is not working properly, and the surface of the camera is hot.
The camera is not working properly, and the surface of the camera is hot.
▶
Check that you have properly connected the camera to an appropriate power source.
Color is not correct.
Color is not correct.
▶
Check the setting of WHITE BAL SETUP menu .
The screen flickers continually.
The screen flickers continually.
▶
Check that the camera is not pointing at the sun.
The camera is out of focus.
The camera is out of focus.
▶
Check that you have properly adjusted the zoom/focus adjustment lever on the lens.
