background image

Limited Warranty

 

 

21

 

 

Limited Warranty 

 

Northern Tool + Equipment shall warranty any

 

piece of equipment manufactured, or parts of equipment 

manufactured, to be free from defects in material or workmanship for a period of 90 days from the date of purchase 
by user. This warranty applies to the original purchaser of the equipment and is non transferable. Verification of 
purchase is the responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the 
equipment has failed due to lack of proper maintenance. Any misuse, abuse, alteration or improper installation or 
operations will void warranty. Determining whether a part is to be replaced or repaired is the sole decision of 
Northern Tool + Equipment. 

 
NOTE: 

Some services performed by parties other than Northern Tool + Equipment may void warranty. 

 
This warranty covers parts only. It will not provide for replacement of complete products due to defective parts. 
Components not manufactured by Northern Tool + Equipment are guaranteed by their manufacturer and can be 
serviced at factory-authorized locations near you. Any costs incurred due to replacement or repair of items outside 
of a Northern Tool + Equipment approved facility is the responsibility of the buyer and not covered under warranty. 
Northern Tool + Equipment can supply you with the service center location in your area.

 

 
This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, 
windstorm, acts of God, applications not approved by Northern Tool + Equipment in writing, corrosion caused by 
chemicals, use of replacement parts which do not conform to manufacturer’s specifications, and damage caused by 
vandalism. Additional exclusions: loss of running time, inconvenience, loss of income, or loss of use, including any 
implied warranty of merchantability of fitness for a specific use. 
 
Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical 
contact by the public. This warranty does not cover any personal injury or damage to surrounding property caused 
by failure of any part.  
 
This warranty is in lieu of any other warranty expressed or implied and Northern Tool + Equipment assumes no 
other responsibility or liability outside that expressed within this warranty. 
 
 
Please fill in the following information and have it on hand when you call in on a warranty claim. 
 
Customer Number: ______________________________________________________________ 
 
Date of Purchase: _______________________________________________________________ 
 
Northern Tool + Equipment Serial Number: __________________________________________ 
 
Item Number: __________________________________________________________________ 
 
 

Summary of Contents for M109271D























Reviews: