background image

LED10 User Manual 

 

3625 Cincinnati Avenue, Rocklin CA 95765 ● 855-388-7422 ● www.northernvideo.com 

Important Information 

Safety Warning 

To use the product safely and correctly and to keep users from suffering harm or property loss, 
please  observe  the  following  safety  precautions  when  installing,  using  and  maintaining  this 
device.    Please  read  this  handbook  before  operating  the  product  and  keep  the  handbook  for 
future reference. 
 

 

Read and observe all the warnings and illustrations. 

 

Do not open or remove the rear cover, of the product. There are no user serviceable parts 
inside. 

 

Do  not  place  any  articles  on  the  product.  The  product  may  be  damaged  if  foreign  matter 
enters the housing.       

 

Do  not  bend  the  power  line,  especially  on  the  plug,  outlet  or  the  place  where  the  cable 
extends out of the product. 

 

To reduce the risk of fire or explosion, do not put the product in any flammable or corrosive 

gaseous environment. 

 

Please remove power to the unit immediately and take it to a qualified technician if there is 
smoking, odors or abnormal noise occurs. 

 

Only qualified technicians should maintain the product if the product experiences any fo the 

following: damage to plug, is splashed with any liquids, exposed to rain or humidity, not able 

to function properly or dropped. 

 

Do  not  expose the  product  to  the  rain  or  chemicals.  If  the product  gets wet,  please  dry  it 

before turning on the power. 

 

Turn off the power when cleaning the product. 

 

Installment of unsuitable facility might cause the fall of the facility or other accidents. Fasten 

the screw of every component when installing. 

 

Be  careful  when  maintaining  inner  body  even  if  the  power  is  cut  off.  Some  internal 
components  can  continue  to  supply  power  which  is  dangerous  to  people  evenafter  the 

power is cut off. 

Notes 

 

Please  place  the  monitor  in  flat,  stable  and  dry  area  and  avoid  direct  sunlight,  high 
temperature, humidity, dust and corrosive gas. 

 

If  the  product  is  installed  on  the  wall,  please  make  sure  the  wall’s  load  bearing  is  enough 

support 10 times the monitors weight. To avoid falling and hurting people, install according 
to the instructions provided with your mounting hardware. 

Summary of Contents for LED10











Reviews: