Northern Industrial Tools 1200-LB Owner'S Manual Download Page 9

 

Page      of 12 

9

 

OPERATION

 

WARNING: 

Before  using  the  utility  dump  cart,  review  the  instructions  below  and  safety 

information. Failure to follow these instructions may result in property damage or injury to the operator 
or bystanders.

 

 

USING YOUR UTILITY DUMP CART 

1. 

DO NOT

 exceed rated capacity of 1200 lbs. (544.8kg). 

2. 

ALWAYS 

secure and lock the utility cart to the vehicle hitch before operating. 

3. 

ONLY

 use approved vehicles when towing the dump cart (Lawn/Garden Tractors and ATVs) 

4. 

NEVER 

tow the utility dump cart with box raised.

 

5. 

DO  NOT

 over fill the utility dump cart. Overflow loads can cause the cart and towing vehicle to lose 

traction and skid out of control.

 

6. 

ONLY

  fill  the  dump  cart  to  a  comfortable  dumping  load.  Extremely  heavy  loads  will  be  difficult  to 

operate and dump.

 

7. 

ALWAYS

 use the dump cart for its intended purpose. 

8. 

ALWAYS

 make sure that the tow vehicle and the combined weight of the operator MUST BE greater 

than the load of the cart weight for proper control.

 

9. 

DO NOT

 use cart on public highways or roads. 

10. 

NEVER 

exceed 10 MPH when towing the dump cart. 

11. 

DO NOT 

make sharp turns that may cause the Lawn/Garden Tractor or ATV tires to rub against the 

utility dump cart.

 

12. 

ALWAYS

 slow down before turning. 

13. 

ALWAYS

 use caution when backing the utility cart. To prevent the cart from jackknifing, always back 

up in a straight line.

 

MAINTENANCE 

 

Maintain your dump cart. 

It is recommended that the general condition of any dump cart be 

examined before it is used. Keep your dump cart in good repair by adopting a program of conscientious 
repair and maintenance. Have necessary repairs made by qualified service personnel.

 

 

After each use clean material out of the cart box.

 

 

Rinse/dry inside and outside of the dump cart after each use.

 

 

Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE OF 25 PSI.

 

 

Regularly grease the axle and the wheel bearing area or when needed.

 

 

Periodically check all fasteners for tightness.

 

 

Annually clean and lightly lubricate parts.

 

 

Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.

 

 

Never exceed load capacity rating of 1200 lbs. (544.8kg); doing so will damage the utility dump cart.

 

 

STORAGE 

  Never allow material to remain in the utility dump cart for extended periods of time. 

  Before storing make sure the cart is clean and dry. 

  Store indoors or protected area during severe weather and winter months. 

  When storing outside, always keep the tongue a little higher than the back of the cart to allow moisture 

to easily run out the back; this ensures that moisture will not accumulate in the box. 

Summary of Contents for 1200-LB













Reviews: