background image

10   ACCESSORIES

7600 SERIES ACCESSORIES

5400 SERIES ACCESSORIES

15

E

E

N

N
G

G

L

L

II

S

S

H

H

11   KEY TO CAUTIONS AND LIMITATIONS 

CONTAINED IN NIOSH APPROVAL LABELS

A

– Not for use in atmospheres containing less than 19.5 %

Oxygen.

– Not for use in atmospheres immediately dangerous to

life or health.

– Do not exceed maximum use concentrations established

by regulatory standards.

– Follow established cartridge or canister change sched-

ules or observe ESLI to ensure that cartridge and canis-
ters are replaced before breakthrough occurs.

– Failure to properly use and maintain this product could

result in injury or death.

– The Occupational Safety and Health Administration regu-

lations require gas-proof goggles to be worn with this
respirator when used against formaldehyde.

L

– Follow the manufacturer’s User’s Instructions for chang-

ing cartridges, canisters, and/or filters.

– All approved respirators shall be selected, fitted, used,

and maintained in accordance with MSHA, OSHA, and
other applicable regulations.

– Never substitute, modify, add or omit parts. Use only

exact replacement parts in the configuration as specified
by the manufacturer.

– Refer to User’s Instructions, and/or maintenance manu-

als for information on use and maintenance of these 
respirators.

P

– NIOSH does not evaluate respirators for use as surgical

masks.

S

– Special or critical User’s Instructions and/or specific use

limitations apply. Refer to User’s Instructions before don-
ning.

11.1  S -  SPECIAL USER’S INSTRUCTIONS

Apply an anti-fog compound to the inside of the lens if
the respirator will be used at temperatures below 32°F
(0°C). This will reduce fogging on the inside of the face-
piece lens so the user can continue to see through it.

If the air-purifying elements have End-Of-Service-Life
Indicators, you must be able to see the End-of-Service-
Life Indicators without manipulation of the cartridges or
facepiece while wearing the respirator.                           

Refer to specific user instructions supplied with car-
tridges for additional ESLI information.

Do not use the Back Pack accessory with air-purifying
elements that have End-Of-Service-Life Indicators,
because you will not be able to see the End-of-Service-
Life Indicators while wearing the respirator.

If you cannot see the indicators, do not use the respira-
tor because you will not know when the cartridge has
expired. Should this occur, and you remain in the con-
taminated work area, you risk exposure to hazardous
quantities of the air contaminant which can result in seri-
ous injury, illness or death.

WARNING

CATALOG
NUMBER

DESCRIPTION

7700-21

Fit Test Adapter

7600-22

Spectacle Assembly (metal, less lenses)

N7500-27

Seal check / Filter Cover

8404

Welding Shield Kit

80100

Spectacle Assembly (plastic, less lenses)

80836

Peel-off Window

7600VA

Voice Amplifier

CATALOG
NUMBER

DESCRIPTION

80944

Antifog Pad

80945

Antifog Cloth

80992

Cleaner / Sanitizer Powder

EZ GUIDE

TM

EZ GUIDE

TM 

CD/ROM

BP1002

Back Pack Accessory

CF2007

Interchangeable Breathing Tube
(Continuous Flow Airline Adapter)

CATALOG
NUMBER

DESCRIPTION

7700-21

Fit Test Adapter

N7500-27

Seal check / Filter Cover

80100

Spectacle Assembly (plastic, less lenses)

80836

Peel-off Window

80944

Antifog Pad

8405

Welding Shield Kit

CATALOG
NUMBER

DESCRIPTION

80945

Antifog Cloth

80992

Cleaner / Sanitizer Powder

EZ GUIDE

TM

EZ GUIDE

TM 

CD/ROM

BP1002

Back Pack Accessory

CF2007

Interchangeable Breathing Tube
(Continuous Flow Airline Adapter)

Summary of Contents for 5400 series
















Reviews: