a
b
2
3
4
1
2
3
4
5
6
6
6
9
2
2
Tighten set screw
flush with surface.
Q
.
Product unable to adjust manually during free state?
A. Full product must be assembled and installed onto wall plate to
gain support in order to move arm upright or down.
Q. Product cannot hovered as it is during upright or down
movement after Installed?
A. Monitor must be installed and pressure (Torque) must be
readjust (Refer to G torque adjustment).
Q. When monitor is at the max upright or position after Installed?
A. Pressure (Torque) must be re-adjust (Refer to G adjustment).
Q. What size of drill bits used for masonry, concrete wall and wood
stud?
A. Used diameter 10mm drill bits for masonry or concrete wall.
Diameter 4mm for wood stud . Holes depth must be than
60mm+.
To adjust pressure torque , Arm 1 must be held down
and adjusting screw then appeared for adjustment.
F
(
)
5
mm
-
12
°
+
1 2
°
①
③
②
F
（
3mm
）
-
12
°
+
1 2
°
F
（
3mm
）
①
②
360
°
1
2
4
5
1
3
（
5mm
）
F
（
5mm
）
F
（
5mm
）
2
F
F
(
3mm
)
F
(
3mm
)
5
F
(
3mm
)
F
(
3mm
)
3
4
D
、
Display
height
adjustment
G
、
Torque adjustment
"
+
":
Torque increase direction shown fig
-
1
"-":
Torque decrease direction shown fig
-
2
Notes
：
Ensure display weight is within load range
.
If display and keyboard tray can be hovered at any height after
display installed. No adjustment needed
.
1
.
If display and keyboard tray rise up automatically after display
installed
,
adjust the following
:
One man hand press down the
screen
,
the other wind set screw at the bottom of upper arm
at joint to
'
–
'
direction to reduce torque by using F
,
5mm.
Allen key as shown in Fig
-
1 and Fig-2 until display and keyboard
tray can be hovered at any point of positions
.
2
.
C
、
W
orkstation
assembly
& installation
H
、
Display rotation
I
、
Keyboard tray extends adjustment
J
、
Keyboard
tray
angle
adjustment
F
、
Power
and display lines installation
Declind
adjustment
:
Inclined
adjustment
:
①
Turn screw anti-clockwise direction using 3mm Allen key D to
release.
②
Turn screw clockwise direction using 3mm Allen key
D to tilt upright angle.
③
Turn screw clockwise direction using
3mm Allen to tighten and secure set angle
.
①
Turn screw anti-clockwise direction using 3mm Allen key D to
tilt down side angle.
②
Turn screw clockwise direction using
3mm Allen to tighten and secure set angle
.
Inclined
adjustment
Declind
adjustment
Warning:
Ensure screws are
secured firmly.
Tighten set screw
flush with surface.
b
a
Loosen screw but
not drop off.
Loosen screw but
not drop off.
K
、
Common Q & A.
I f
d i s p l a y
a n d
k e y b o a r d
t r a y
a t
t h e
l o w e s t
p o s i t i o n
a f t e r
installation
,
repeat
#
2 procedures but winding set screws to
' + '
direction to increase torque as Fig
-
1 and Fig-2 until display and
keyboard tray can be hovered at any point of positions
.
3
.
E. Display installation
Warning:
Ensure screws are
secured firmly.
Note
：
The
pre
-
sre
force
is
at
the
medium
.
9
