background image

88052959        09/13

Telescoping Pole Saw/Chainsaw

For Customer Service, please call 

1-800-348-5004

 or 

email 

[email protected]

1

Model: 52959

CALIFORNIA PROPOSITION 65
WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer,
birth defects, or other
reproductive harm. Wear
protective gear.
WARNING: This product or its
power cord may contain
chemicals, including lead, known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
after handling.
Important!

When using equipment, a few safety
precautions must be observed to
avoid injuries and damage. Please
read the complete operating manual
with due care. Keep this manual in a
safe place, so that the information is
available at all times. If you give the
equipment to any other person, give
them these operating instructions as
well. We accept no liability for
damage or accidents which arise due
to non-observance of these
instructions and the safety
information herein.

CAUTION:
FOR YOUR OWN SAFETY READ
INSTRUCTION MANUAL
COMPLETELY AND CAREFULLY
BEFORE OPERATING THIS
TELESCOPING POLE SAW/
CHAINSAW.

SPECIFICATIONS
Motor Amp:

 6.25 Amp

Bar Length:

 8”

Comfort Grips
Maximum Extension:

 7.5 ft.

Voltage:

120V

Idle Speed:

 8500 RPM

Oregon® Bar & Chain

Any failures made in following the
safety regulations and and
instructions may result in an
electric shock, fire and/or serious
injury.

UNPACK

1. Unpack all parts and lay them on
a flat, stable surface.
2. Remove all packing materials and
shipping devices if applicable.

3. Make sure the contents are
complete and free of damage. If
you find that parts are missing or
damaged, contact your dealer.
Using an incomplete or damaged
product may cause damage to
people or property.
4. Ensure you have all the
accessories and tools needed for
assembly and operation. This also
includes suitable personal
protective equipment.

INTENDED/NON-INTENDED USE
: POLE SAW

The pole saw is intended for cutting
trees and other wood from the
ground. It must only be operated in
the garden area. Do not use it for
any purpose that it was not
intended. The pole saw is intended
to be operated in the way specified
in this instruction manual. Read
and observe instructions and
warning signs attached to the
machine before every use. It is
intended to be used with original
spare parts or spare parts
authorized by the manufacturer. If
non-authorized spare parts or non-
original spare parts, the warranty
will be voided. The operator is
liable for any resulting injuries or
damages.

Summary of Contents for 52959
















Reviews: