Nortel RLC Installation And Administration Manual Download Page 305 | Manualshive

Page: 305 / 466

background image

RLC Installation and Administration Guide

279

June 2005

Administration

Network Statistics

Network Statistics allow you to see the performance over the last 24 hours of the
remote units connected to the logged-on RLC. Use these statistics to identify
periods when other network activity can adversely affect Remote Gateway 9100
Series system performance. This screen shows remote unit performance in terms
of the transmission and reception of frames and packets, similar to the
following.

To display the Network Statistics screen, refer to “Displaying the Network
Statistics screen” on page 280. To obtain the definitions for the statistics
presented on the Network Statistics screen, refer to “Network Statistics field
descriptions” on page 281.

«
...
303
304
305
306
307
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

ShareCenter DNS-320L

Brand: D-Link Pages: 4

Brand: Parkside Pages: 55

Brand: Parkside Pages: 34

Brand: Maxim Pages: 26

Brand: NetComm Pages: 3

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

ST62GP-EMU2 HDS2 Series

Brand: STMicroelectronics Pages: 58

Brand: Netis Pages: 16

Brand: FDI Pages: 2

Brand: Dahua Pages: 113

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

Brand: SriHome Pages: 12

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

PXI PXITM -1000

Brand: National Instruments Pages: 55

Brand: Cradlepoint Pages: 2

Brand: Neousys Technology Pages: 39

Brand: CyberResearch Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands