Nortel RLC Installation And Administration Manual Download Page 114

Page: 114 / 466

RLC Installation and Administration Guide

Installing the RLC

Standard 4.0

Plug

, the female DB-9 connector of the RLC Multi-I/O cable (Basic or

Enhanced), into the Remote Gateway 9100 Series administration PC.

Plug

, the second male DB-15 connector of the RLC Multi-I/O cable–

Enhanced, into a DB15 to RJ45 adapter (NT7R93CA).

Note:

The RLC Multi-I/O cable–Enhanced ships with this adapter. This

adapter is not an active transceiver.

Plug one end of a

shielded

(to meet CISPR B requirements) CAT 5

data cable of sufficient length to reach your Ethernet hub into the other
side of the DB15 to RJ45 adapter connected to P2.

Plug the other end of the CAT5 data cable into your Ethernet hub.

Proceed to “Verifying the installation” on page 89.

Plug

, the second 25-pair connector, into the cross-connect device

serving the local telephones that you want to attach to RLC ports not
needed for remote service purposes.

IF installing the

THEN proceed to

RLC Multi-I/O cable–Basic,

“Verifying the installation” on page
89.

RLC Multi-I/O cable–Enhanced in
North America,

step 5.

RLC Multi-I/O cable–Enhanced in
a location other than North
America,

step 6.

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands