manualshive.com logo in svg

Nortel Passport 7400, Hardware Installation, Maintenance, And Troubleshooting, Page: 250 / 438

Share
Download
Nortel Passport 7400 Hardware Installation, Maintenance, And Troubleshooting Download Page 250

250   Chapter 37 Hardware procedures

241-7401-240   5.2S1

Installing a rack-mounted alarm panel

Install a rack-mounted alarm panel so that you can monitor the status of a 16-
slot Passport switch if your switch is not installed in a cabinet.

Prerequisites

•

You will need an alarm panel assembly with PEC NTJS74.

Procedure steps

1

Install the alarm panel. Follow the procedure “Installing a 19” rack-
mounted termination panel” (page 205).

2

Connect the alarm panel cable to the alarm cable connector on the alarm
panel. See the figure “Rack-mounted alarm panel” (page 250).

Figure 87
Rack-mounted alarm panel

3

Route the cable down to the shelf assembly and connect it to the door
alarm connector on the back of the shelf. See the figure “Dual alarm shelf
interconnection” (page 377).

PPT 2497 001 AA

Power LED

Alarm cutoff

Minor alarm LED

Major alarm LED

•

•

•

•

•

•

•

•

Alarm cable 
connector

•

•

Summary of Contents for Passport 7400























































































































































































































































































































































































































































Reviews:

No comments