manualshive.com logo in svg

Nortel Passport 5430, Installing And Operating Instructions, Page: 76 / 220

Share
Download
Nortel Passport 5430 Installing And Operating Instructions Download Page 76

Installing and Operating the Passport 5430 Multiservice Access Switch

3-10

306308-A Rev 00

Removing and Installing a Power Supply Filler Panel 

Nortel Networks ships the Passport 5430 with a filler panel in the power supply 
slot reserved for the second power supply. 

Before you can install a second power module, you must remove the power supply 
filler panel. For instructions, see the next section, 

“Removing a Power Supply 

Filler Panel

.” 

If you remove a power supply from the Passport 5430 without replacing it, you 
must install a power supply filler panel to maintain the proper cooling airflow. For 
instructions, see 

“Installing a Power Supply Filler Panel

.” 

Removing a Power Supply Filler Panel

To remove a power supply filler panel:

1.

Using a flat-tip screwdriver, loosen the captive screw that fastens the 
power supply filler panel to the chassis until the filler panel disengages 

(Figure 3-7)

.

Figure 3-7.

Removing a Power Supply Filler Panel

PS1

PS2

FBR0059A

100-240V~ 50-60Hz   25A

DC OK

Summary of Contents for Passport 5430





























































































































































































































Reviews:

No comments