Nortel Passport 5430 Installing And Operating Instructions Download Page 59

Page: 59 / 220

Installing Passport 5430 Customer-Replaceable Units for the First Time

306308-A Rev 00

2-21

Installing a WAN Adapter Module

To install a WAN adapter module for the first time:

Put on an antistatic wrist strap.

For instructions, see “Attaching the Antistatic Wrist Strap” on page 3-2.

Determine which of the four front-panel adapter module slots to use

(Figure 2-18)

Figure 2-18.

Location of WAN Adapter Module Slots

When installing WAN adapter modules in the Passport 5430 WAN adapter
module slots, note the following:

Caution:

Electrostatic discharge can damage hardware. You must wear the

antistatic wrist strap on your arm whenever you handle printed circuit boards.

Note:

The slot labeled Remote Console is reserved for the V.34 modem

adapter module for out-of-band management.

FBR0025A

Passport 5430 front panel

Module 3

Module 4

Module 5

Remote
Console

COM

ISDN BRI

withNT1

Telco

V.34 Modem

DDS

156K/64K
DSU/CSU

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 59 / 220

Search results

Summary of Contents for Passport 5430

Reviews: