Nortel Passport 5430 Installing And Operating Instructions Download Page 126

Page: 126 / 220

Installing and Operating the Passport 5430 Multiservice Access Switch

7-2

306308-A Rev 00

Figure 7-1.

Loosening the Extractor Screws

Gently pull the inside of the board extractors at each end of the system
processor card away from you

(Figure 7-2)

The extractors swing open, pulling the card out of the backplane connectors.

Figure 7-2.

Removing the System Processor Card

Module 3

Module 4

Module 5

Remote
Console

System

Processor

Expansion Card

Voice Processor

COM

ISDN BRI

withNT1

Telco

V.34 Modem

COM

FBR0106A

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Por

t 2

rt 1

rt 2

rt 1

Inser

Extr

act

PMC Slot 2

PMC Slot 1

Expansion Module

Dsync

FBR0099A

LSD

ISDN BRI

withNT1

Telco

RLSD

DTR

V.34 Modem

System

Processor

Module 3

Module 4

Module 5

Remote
Console

Extractors

PCI Slot 1

PCI Slot 2

Passport 5430 chassis

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 126 / 220

Search results

Summary of Contents for Passport 5430

Reviews: