Nortel Passport 5430 Installing And Operating Instructions Download Page 113

Page: 113 / 220

Operating the Passport 5430

306308-A Rev 00

6-3

Table 6-1

describes the system processor card console LEDs.

Table 6-1.

System Processor Card Console LEDs

LED

State

Meaning

PS1

Off

Power is off.

On (green)

Power supply is operating.

Rapid flashing (green)

Power supply failed.

PS2

Off

Power is off.

On (green)

Redundant power supply (optional) is operating.

Rapid flashing (green)

Redundant power supply failed.

Fan

Off

Fan is operating properly.

On (green)

One or more cooling fans stopped operating.

Rapid flashing (green)

Fan failed.

WAN

Off

WAN adapter module was not tested.

On (green)

WAN adapter module is operating properly.

Slow flashing (green)

Module is running its diagnostic tests.

Rapid flashing (green)

Module failed its diagnostic tests.

Mod 2

Off

Module 2 was not tested.

On (green)

Module 2 is operating properly.

Slow flashing (green)

Module 2 is running its diagnostic tests.

Rapid flashing (green)

Module 2 failed its diagnostic tests.

Run

Off

Processor code is not loaded.

On (green)

Passport 5430 is operational.

Slow flashing (green)

Diagnostic tests are running.

Rapid flashing (green)

Diagnostic tests found failures.

Boot

Off

Passport 5430 is not in boot mode.

Slow flashing (green)

Diagnostic tests were successful and the Passport
5430 is booting.

Rapid flashing (green)

Diagnostic tests found failures and the Passport
5430 is booting.

Sys

Off

System processor card was not tested.

(continued)

Summary of Contents for Passport 5430





























































































































































































































Search results

Summary of Contents for Passport 5430

Reviews:

Nortel Passport 5430, Installing And Operating Instructions, Page: 113 / 220

Search results

Summary of Contents for Passport 5430

Reviews: