manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 93 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 93

93

System Configuration Guide

 

Chapter 2
Using the console interface

This chapter describes how to configure and manage the Ethernet Switch 325/425 
using the menu-driven Console Interface (CI).

This chapter covers the following topics:

•

“Accessing the CI menus and screens”

•

“Using the CI menus and screens” on page 94

•

“Main menu” on page 96

Accessing the CI menus and screens

You can access the CI menus and screens locally through a console terminal 
attached to your Ethernet Switch 325/425, remotely through a dial-up modem 
connection, or in-band through a Telnet session. You can connect your console 
cable into any unit in the Ethernet Switch 325/425-only stack for a unified stack 
interface.

For information about SNMP, see your network management documentation.

Note: 

If you have a properly configured BootP server in your network, 

it detects the IP address; you will not need to configure the IP address.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments