manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 85 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 85

Chapter 1 About Ethernet Switches 325 and 425

85

System Configuration Guide

 

Segment switch application

Figure 12

 and 

Figure 13

 show the Ethernet Switch 325/425 used as a segment 

switch to alleviate user contention for bandwidth and eliminate server and 
network bottlenecks. Before segmentation, 88 users had a total bandwidth of only 
10 Mb/s available. After segmentation, 92 users have 40 Mb/s, four times the 
previous bandwidth, while adding 22 dedicated 100 Mb/s connections. This 
configuration can be extended to add more segments without degrading 
performance.

Figure 12   

Ethernet Switch 325 used as a segment switch

Server

Up to

88 users

To

Network

Center

Key

10 Mb/s
100 Mb/s
1000 Mb/s

10BASE-T hubs

Before

After

Up to 20

users

Up to 23

users

To

Network

Center

11113EA

Up to 23

users

Up to 23

users

- 88 users share 10 Mb/s (10/88 Mb/s per user)
- Server bottleneck (10 Mb/s bandwidth)
- Network center bottleneck (10 Mb/s bandwidth)
-Total of 88 users

- Three sets of 23 users; each set shares 10 Mb/s
  (10/23 Mb/s per user)
- Addition of 21 users; each with dedicated
  100 Mb/s bandwidth
- Server with dedicated 100 Mb/s bandwidth
- Network center with dedicated 1 Gb/s full-duplex bandwidth
- Total of 89 users

Ethernet Switch
325-24G

Server

UI

UI Set

25

26

Spd: 10/100/1000T

Act: Activity

LED Status - Amber:10Mps Green:100 Mps Blink:Activity

UI Cmd

Pwr

Console

Ethernet Switch 325-24G

Spd Act

Spd Act

1

2

3

4

5

6

7

8

9

10

11

12

LED Status - Off:Half Duplex Green:Full Duplex

13

14

15

16

17

18

19

20

21

22

23

24

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments