manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 79 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 79

Chapter 1 About Ethernet Switches 325 and 425

79

System Configuration Guide

 

AC power receptacle 

The AC power receptacle accepts the AC power cord which is supplied with the 
switch. For installation outside North America, make sure that you have the 
proper power cord for your region. Any cord used must have a CEE-22 standard 
V female connector on one end and must meet the IEC 320-030 specifications. 

Table 11

 lists specifications for international power cords.

Table 11   

International power cord specifications

Country/Plug description

Specifications

Typical plug

Continental Europe:

•

CEE7 standard VII male plug

•

Harmonized cord (HAR marking 
on the outside of the cord jacket 
to comply with the CENELEC 
Harmonized Document HD-21)

220 or 230 VAC 
50 Hz 
Single phase

U.S./Canada/Japan:

•

NEMA5-15P male plug

•

UL recognized (UL stamped 
on cord jacket)

•

CSA certified (CSA label 
secured to the cord)

100 or 120 VAC 
50–60 Hz 
Single phase

 

228FA

227FA

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments