manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 76 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 76

76

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

LED display panel

Figure 8

 shows the Ethernet Switch 425 LED display panel.

Figure 8   

Ethernet Switch 425 LED display panel

Table 9

 describe the LEDs found in the Ethernet Switch 425.

Table 9   

Ethernet Switch 425 LED descriptions

Label

Command 
Status

Color

State

Meaning

UI

Power status

Green

Blinking

Indicates the switch is in cmd mode. 

On

ON for about 3 seconds when executing a cmd, then 
goes OFF. 

Off

The UI LED should be off, unless active.

GBIC/
Stack

Stack Mode

Green

On

The switch is in standalone mode.

Off

The switch is in stack mode.

Pwr

Power status

Green

on

DC power is available to the switch’s internal circuitry.

Off

No AC power to switch or power supply failed.

Base

Base mode

Green

on

The switch is configured as the stack base unit.

Off

The switch is 

not

 configured as the stack base unit (or is 

in standalone mode).

Amber

Due to a stack error, the unit is unable to maintain the 
stack connection.

Up

Stack mode

Green

Off

The switch is in standalone mode.

On

The switch is connected to the 

upstream

 unit. 

Down

Stack mode

Green

Off

The switch is in standalone mode.

On

The switch is connected to the 

downstream

 unit.

Base

UI

UI 

Set

25

26

M:MGBIC A:Activity

T:1000T

M

LED Status 

- 

Amber:10Mps 

Green:100 

Mps Blink:Activity

GBK/Stack Up

Pwr

Down

T

A

M

T

A

1

2

3

4

5

6

7

8

9

10

11

12

LED Status 

- 

Off:Half 

Duplex 

Green:Full

Du

13

4

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments