Nortel 425-24T Configuration Manual Download Page 469

Page: 469 / 488

469

System Configuration Guide

Appendix F
Technical specifications

This appendix provides technical specifications for the Ethernet Switch 325/425.

Environmental specifications

Table 169

lists environmental specifications for the Ethernet Switch 325/425.

Electrical parameters

Table 170

lists power electrical parameters for the Ethernet Switch 325/425.

Table 169

Environmental specifications

Parameter

Operating specification

Storage specification

Temperature

0°

to 40°C (32° to 104°F)

-25° to 70°C (-13° to 158°F)

Humidity

85% maximum relative humidity,
noncondensing

95% maximum relative humidity,
noncondensing

Altitude

3024 m (10,000 ft)

Table 170

Electrical parameters

Parameter

Electrical specification

Input Voltage

100 to 240 VAC @ 47 to 63 Hz

Input Power
Consumption

46 W maximum (Ethernet Switch 325)

50 W maximum (Ethernet Switch 425)

Input Volt
Amperes Rating

65 VA maximum

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 469 / 488

Search results

Summary of Contents for 425-24T

Reviews: