manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 402 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 402

402

Chapter 12 Configuring the switch using Web-based management

320985-A Rev 01

 

Configuring Rate Limiting

Broadcast Rate Limiting is a box-oriented feature which allows you to configure 
threshold limits for either broadcast or multicast packets ingressing on a port for a 
given time interval (in packets per second). If the configured threshold exceeds on 
a port, the switch will drop extra packets received. No SNMP trap or syslog is 
generated in case of congestion.

Configuring Rate Limiting

To configure Rate Limiting using the Web-based management system:

1

From the main menu, choose 

Application > Rate Limiting

.

The 

Rate Limiting

 page opens 

(Figure 166)

.

Figure 166   

Rate Limiting page

Table 154

 describes the items on the 

Rate Limiting

 page.

Table 154   

Rate Limiting page items

Section

Description

Port

The port number that corresponds to the selected 
switch.

Unit

The number of the unit in the stack.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments