Nortel 425-24T Configuration Manual Download Page 380

Page: 380 / 488

380

Chapter 11 Administering the switch using Web-based management

320985-A Rev 01

From the main menu, choose

Administration > Reset

The reset warning message displays

(Figure 153)

Figure 153

Reset page message

Click

To reboot the Ethernet Switch 425-24T in its stack mode without making changes
(since your last Submit request):

From the main menu, choose

Administration > Reset

The

Reset

page opens

(Figure 154)

Figure 154

Reset page

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 380 / 488

Search results

Summary of Contents for 425-24T

Reviews: