Nortel 425-24T Configuration Manual Download Page 353

Page: 353 / 488

Chapter 9 Configuring the switch using Device Manager

353

System Configuration Guide

Table 134

describes the Fan tab fields.

Banner tab

The

Banner

tab allows you to specify banner display in TELNET. You can

specify either the default banner or a custom banner.

To open the

Banner

tab:

Select the chassis.

From the main menu, choose

Edit > Chassis

The

Chassis

dialog box opens

(Figure 133 on page 344)

with the

System

tab

displayed.

Click the

Banner

tab.

The

Banner

tab opens

(Figure 139)

Table 134

Fan tab fields

Field

Description

Desc

The fan type.

OperStat

The operational state of the fan. Values include:

•

other: Some other state.

•

notAvail: This state is not available.

•

removed: Fan was removed.

•

disabled: Fan is disabled.

•

normal: Fan is operating in normal operation.

•

resetInProg: A reset of the fan is in progress.

•

testing: Fan is doing a self test.

•

warning: Fan is operating at a warning level.

•

nonFatalErr: Fan is operating at error level.

•

fatalErr: An error stopped the fan operation

•

notConfig: Fan needs to be configured. The allowable values are
determined by the component type.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 353 / 488

Search results

Summary of Contents for 425-24T

Reviews: