manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 352 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 352

352

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Fan tab

The 

Fan

 tab provides read-only information about the operating status of the 

switch fans.

To open the 

Fan

 tab:

1

Select the chassis.

2

From the shortcut menu, choose 

Edit > Chassis

.

The 

Chassis

 dialog box opens 

(Figure 133 on page 344)

 with the 

System

 tab 

displayed.

3

Click the 

Fan

 tab.

The 

Fan

 tab opens 

(Figure 138)

.

Figure 138   

Edit Chassis dialog box — Fan tab

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments