manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 350 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 350

350

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

Figure 136   

Edit Chassis dialog box — Agent tab

Table 132

 describes the 

Agent

 tab fields.

PowerSupply tab

The 

PowerSupply

 tab provides read-only information about the operating status 

of the switch power supplies.

To open the 

PowerSupply

 tab:

1

Select the chassis.

2

From the shortcut menu, choose 

Edit > Chassis

.

Table 132   

Agent tab fields

Field

Description

NextBootIpAddr

The IP address to be used the next time the switch is booted.

NextBootNetMask

The subnet mask to be used the next time the switch is 
booted.

LoadServerAddr

The IP address of the load server for the configuration file 
and/or the image file. If not used, then the value is 0.0.0.0. 

ImageFileName

Name of the image file(s) currently associated with the 
interface. When the object is not used, the value is a zero 
length string. 

ValidFlag

Indicates if the configuration and/or image file(s) were 
downloaded from this interface and if the file names have not 
been changed.

BootRouterAddr

The IP address of the boot router for the configuration file and/
or the image file. 

MacAddr

The MAC address of the switch.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments