manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 338 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 338

338

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

The following sections provide a description of the tabs in the Edit > Unit dialog 
box and details about each item on the tab.

Unit tab

To open the 

Unit

 tab:

➨

From the Device Manager main menu, choose 

Edit > Unit

.

The 

Unit

 dialog box 

(Figure 128)

 opens with the 

Unit

 tab displayed. 

Figure 128   

Unit dialog box

Table 124

 describes the 

Unit

 tab fields.

Rate Limit tab

To open the 

Rate Limit

 tab:

Table 124   

Unit tab fields

Field

Description

Type 

Specifies the type number.

Descr 

Specifies the type of switch.

Ver 

Specifies the hardware version number of the switch.

Sernum

Specifies the serial number of the switch.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments