manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 335 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 335

Chapter 8 Ethernet port management using the CLI

335

System Configuration Guide

 

default auto-negotiation-advertisements command

The

 default auto-negotiation-advertisements 

command sets default 

advertisements for the switch. The syntax for the

 default 

auto-negotiation-advertisements 

command is:

default auto-negotiation-advertisements [port <portlist>]

The

 default auto-negotiation-advertisements 

command is in the 

interface configuration command mode.

Table 123

 describes the parameters and variables for the

 default 

auto-negotiation-advertisements

 

command. 

This feature allows you to customize the capabilities that you advertise. It also 
allows you to control the capabilities that are advertised by the Ethernet switch as 
part of the auto-negotiation process.

Table 123   

default auto-negotiation-advertisements command

Parameters and values

Description

port <portlist>

Enter ports for which you want to set default 
advertisements.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments