manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 293 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 293

Chapter 7 System configuration using the CLI

293

System Configuration Guide

 

sntp sync-now command

The 

sntp sync-now 

command forces a manual synchronization with the NTP 

server.

The syntax for the 

sntp sync-now 

command is:

sntp sync-now

The 

sntp sync-now 

command is in the config command mode.

The 

sntp sync-now 

command has no parameters or variables. 

sntp sync-interval command

The 

sntp sync-interval 

command specifies recurring synchronization with 

the NTP server in hours relative to initial synchronization. The syntax for the 

sntp sync-interval 

command is:

sntp sync-interval 

<

0-168>

The 

sntp sync-interval 

command is in the config command mode. 

Table 88

 describes the parameters and variables for the 

sntp sync-interval 

command.

Note: 

You must have SNTP enabled before this command can take 

effect.

Table 88   

sntp sync-interval command parameters and variables

Parameters and 
variables

Description

<0-168>

Enter the number of hours you want for periodic synchronization 
with the NTP server.

Note

: 0 is boot-time only, and 168 is once a week; the default 

value is 24 hours.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments