manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 258 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 258

258

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

no ip address unit command

The 

no

 

ip address unit 

command sets the IP address for the specified unit in 

a stack to all zeros (0). The syntax for the 

no

 

ip address unit 

command is:

no ip address unit <1-8>

The 

no

 

ip address unit 

command is in the config command mode. 

Table 64

 describes the parameters and variables for the 

no

 

ip address unit 

command. 

default ip address unit command

The 

default ip address unit 

command sets the IP address for the 

specified unit in a stack to all zeros (0). The syntax for the 

default ip 

address unit 

command is:

default ip address unit <1-8>

The 

default ip address unit 

command is in the config command mode. 

Note: 

When you change the IP address or subnet mask, you may lose 

connection to Telnet and the Web. 

Table 64   

no ip address unit command parameters and variables

Parameters and 
variables

Description

unit <1-8>

Zeroes out the IP address for the specified unit.

Note: 

When you change the IP address or subnet mask, you may lose 

connection to Telnet and the Web.You also disable any new Telnet 
connection, and you must connect to the serial console port to configure 
a new IP address. 

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments