Nortel 425-24T Configuration Manual Download Page 239

Page: 239 / 488

Chapter 6 System configuration using the Console Interface

239

System Configuration Guide

Figure 87

Software Download screen for an Ethernet Switch 325/425 stack

Table 53

describes the

Software Download

screen fields.

Table 53

Software Download screen fields

Field

Description

Image Filename

The Ethernet Switch 325/425 software image load file name.

Note

: Certain software releases may require you to download two images: the boot code

image and the agent image. For proper operation of the switch, the new boot code image
must be downloaded before the agent image is downloaded.

Default value

Zero-length string

Range

An ASCII string of up to 30 printable characters

Diagnostics
Filename

The Ethernet Switch 325/425 diagnostics file name.

Default value

Zero-length string

Range

An ASCII string of up to 30 printable characters

TFTP Server IP
Address

The IP address of your TFTP load host.

Default value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented
as a decimal value, separated by a decimal point

Software Download

Software Image Filename: [ docu/hummingbird_360.img ]

Diagnostics Image Filename: [ ]

TFTP Server IP Address: [ 198.202.188.174 ]

Start TFTP Load of New Image: [ No ]

Enter text, press <Return> or <Enter> when complete.

Press Ctrl-R to return to previous menu. Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 239 / 488

Search results

Summary of Contents for 425-24T

Reviews: