manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 206 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 206

206

Chapter 5 Using the Web-based management interface

320985-A Rev 01

 

Viewing summary switch information

You can view summary information about the switch. For example, the unit 
number and its corresponding physical description and serial number. 

To view summary switch information:

➨

From the main menu, choose

 Summary > Switch Information

.

The 

Switch Information 

page opens 

(Figure 75)

.

Figure 75   

Switch Information page

Table 44

 describes the fields on the 

Switch Information

 page.

Table 44   

Switch Information page fields

Item

Description

Module Description

The factory set description of the policy switch.

GBIC Description

The factory set description of the sub-component/GBIC.

Firmware Version

The firmware version of the policy switch.

Software Version

The version of the running software.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments