manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 200 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 200

200

Chapter 5 Using the Web-based management interface

320985-A Rev 01

 

Access to the Web management interface must also be enabled for the switch (the 
default setting) using the Console Interface. For information about enabling Web 
access, refer to 

“TELNET/SNMP/Web Access Configuration screen” on 

page 234

.

Logging in to the Web-based management interface

Before you log in to the Web-based management interface, use the console 
interface to verify the VLAN port assignments and to ensure that your switch 
CPU and computer are assigned to the same VLAN. If the devices are not 
connected to the same VLAN, the IP address will not display the home page.

To log in to the Web-based management interface:

1

Start your Web browser.

2

In the address bar, type the IP address for your host switch, for example,

 

http://192.168.151.175

, and press 

Enter

.

The home page opens 

(Figure 72)

.

Figure 72   

Web-based management interface home page

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments