manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 191 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 191

Chapter 4 Getting Started with Device Manager

191

System Configuration Guide

 

To change the type of statistics displayed, select a different type from the show 
list at the bottom of the dialog box.

The statistics are updated based on the poll interval shown at the bottom of the 
dialog box. You can select a different polling interval.

Buttons for bar, pie, and line graphs are located at the bottom of a 

statistics

 dialog 

box.

See the next section, 

“Viewing statistics as graphs”

, for instructions to use these 

buttons.

You can export the statistics to a tab-separated file format and import the file into 
other applications. To export the information, use the 

Export Data

 button below 

the table.

Viewing statistics as graphs

To create a graph for an object:

1

Select the object or objects to be graphed.

See 

“Selecting objects” on page 180

.

2

Do one of the following:

•

On the toolbar, click 

Graph Selected

.

•

From the shortcut menu for the object, choose 

Graph

.

•

From the main menu, choose

 Graph > Chassis 

or 

Graph > Port

.

A statistics dialog box opens with tabs for different categories of statistics for 
the selected object 

(Figure 70)

.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments